cecotec BOLERO COOLMARKET COMBI 356 WHITE D Manual De Instrucciones página 35

ENGLISH
Fig. 17
25. Lower hinge
26. Special flange screw
27. Adjustable lower legs
Fig. 18
28. Lower hinge pin
Fig. 21
29. Upper door's upper-left hinge
Fig. 22
30. Upper door connector
31. Refrigerator connector
32. Refrigerator connector
Fig. 23
33. Self-tapping screw
1. Open the door, remove the door shelves (to prevent any damage) and then close the door.
To remove the shelves, slightly press the shelf and move it upwards. Fig. 6
2. Unscrew the screw on the upper-right hinge (1), then remove the upper hinge cover (2).
Carefully unplug the electrical connector (3) underneath. Fig. 7
3. Press the side of the door switch (4) and pull it upwards to separate it from the upper-right
hinge cover (2). Insert the door switch (4) into the upper-left hinge cover (5) (included in
the plastic bag). Keep the upper-right hinge cover (2). Fig. 8
Unplug connectors (A) and (B). Then unscrew the screws (6) with an 8 mm drill or a
4.
spanner and remove the upper-right hinge (7). Then fit the connectors (A) and (B) into
the hole as shown in figure 9. After this process, the refrigerator door will be unstable. Be
sure to hold it in place so as not to damage it. Fig. 9
Carefully lift the upper door to remove it from the middle hinge. Then place the upper door
5.
on a soft surface with the inside facing upwards. Fig. 10
6. Insert the right screw gap cover (9) (included in the plastic bag) into the upper-right side
where the upper-right hinge was located. Then, remove the left screw gap cover (10) from
the upper-left side of the refrigerator and put it away. Fig. 11
7. Remove the upper-left side door cover (11) and remove the connector (12). Remove the
upper-right side door cover (13) and place the connector (14) inside. Replace the upper
side door covers (11 and 13) Fig. 12
On the upper door's right side, unscrew the screw (15) and remove the dowel (16) from
8.
the door stop (17). On the upper door's left side, insert the left door stop (18) and the left
B OL E R O COO LM ARKET CO M BI 3 5 6 WHIT E/INOX/
68
DA R K /WHITE GLASS/BLAC K GLASS D
dowel (19) (included in the plastic bag) and secure it with the screw (15). Keep the right
door stop and dowel. Fig. 13
9. Use the Allen key (included in the plastic bag) and a Phillips screwdriver to loosen the
screws and remove the upper-right hinge from the lower door. Then carefully lift the door
up and remove it. Then carefully lift the door up and remove it. Fig. 14
10. Place the lower door on a soft surface with the inside facing up. On the lower door's right
side, unscrew the screw (22) and remove the dowel (21) from the door stop (20). On the
lower door's left side, insert the left door stop (23) and the left dowel (19) (included in the
plastic bag) and secure it with the screw (15). Keep the right door stop and dowel. Fig. 15
11. Replace the screw gap covers and screw the centre plate to the right. Fig. 16
12. Tilt the refrigerator carefully to gain access to its base. Remove the two adjustable lower
legs (27), then remove the lower hinge (25) by unscrewing the screws (26). Fig. 17
13. Loosen the lower hinge pin and remove it. Rotate the hinge and reinsert the lower hinge
pin (28), then tighten it. Fig. 18
14. Place the lower hinge on the left side of the refrigerator base and secure it with the
screws (26). Replace the adjustable lower legs and partially secure them. Fig. 19
15. Place the refrigerator in an upright position and carefully insert the lower door into
the upper hinge of the lower door. At this point, the door will not be attached to the
refrigerator. Hold it firmly so that it does not fall off. Install the left hinge (in the plastic
bag) making sure that the lower door is secured in place. Fig. 20
16. Position the upper door on the left side and place the middle hinge shaft in the upper
door's bottom hole. Install the upper-left hinge (29) (included in the plastic bag) and
screw it with the screws removed in step 9 (6). At this point, the door will not be attached
to the refrigerator, but hold it firmly so that it does not fall off. Fig. 21
17. Remove connectors 31 and 32 from the top left side of the refrigerator. Connect 30 to 31.
Then plug connector 32 to the door switch located on the upper-left hinge cover. Fig. 22
18. Install the upper left hinge cover (5) using the screw (33) as shown in figure 23, on the top
of the refrigerator. Fig. 23
19. Open the upper door, reinstall the shelves, and close the door.
Please note
- If the refrigerator has a handle, you must reverse its position by following these
instructions:
- Remove the covers from the handle screws and then loosen the screws. Pull the handle to
remove it and replace it on the right side. Screw the screws back in and place the covers.
Fig. 24
Fig. 24
1. Handle covers
Special screws
2.
3. Door handle
B OLERO CO OLMARKET COMBI 356 WHITE/IN OX/
DARK/W HITE GLAS S/ BLACK GLAS S D
ENGLISH
69