Cata I 604 B Instrucciones De Uso página 15

THIS APPLIANCE IS CONCEIVED FOR DOMESTIC USE
ONLY. THE MANUFACTURER SHALL NOT IN ANY WAY BE
HELD RESPONSIBLE FOR WHATEVER INJURIES OR
DAMAGES ARE CAUSED BY INCORRECT INSTALLATION OR
BY UNSUITABLE, WRONG OR ABSURD USE.
The manufacturer declares that this product meets all the
essential requirements for low voltage electrical material set
out in European directive 2006/95/EEC of 12 December 2006
and for electromagnetic compatibility as required by
European directive 2004/108/EEC of 15 December 2004.
Operating Principle (Fig. 1)
It exploits the electromagnetic properties of most cooking
vessels.
The coil (inductor) which produces the electromagnetic field
is operated and controlled by the electronic circuit.
The heat is transmitted to food by the cooking vessel itself.
The cooking process takes place as described below.
- loss of heat is minimum (high efficiency)
- the system stops automatically when the vessel is removed
or even just lifted from the hob
- the electronic circuit guarantees maximum flexibility and
fine adjustments.
(Fig. 1)
1 vessel
2 induced current
3 magnetic field
4 inductor
5 electronic circuit
6 power supply
User's Instructions (Fig. 2)
1 Encendido/apagado ON/OFF
2 Minus –
3 Plus +
4 Cooking zone
5 Setting level display
6 Zone selection lights
Installation
All operations relative to installation (electric connection)
should be carried out by skilled personnel in conformity with
the rules in force.
As for the specific instructions see part pertaining to
installer.
Switching the Touch Control ON/OFF "Z"
After mains voltage is applied the control initializes for
approx. 1 second before it is ready for operation. After a
reset all displays and LEDs glow for approx. 1 second. When
this time is over all displays and LEDs extinguish and the
control is in the stand-by mode.
Press the ON/OFF (1) button to switch the touch control on.
The cooking zone displays show a static "0".
If a cooking zone is in the "hot" status, the display shows a
static "H" instead of "0". The bottom right dot is blinking in
1 second intervals on all cooking zone displays to indicate
that no cooking zone is selected at the moment.
After switching-ON the electronic control remains activated
for 20 seconds. If no cooking zone or timer selection follows
within this period of time, the electronic control
automatically switches back into the stand-by-mode.
The control can only be switched-ON if it identifies the
ON/OFF key alone being operated. Should it recognize key
activation other than that, the control remains in the
standby- mode.
If the child safety feature is active when switching on, all
cooking zones show "L", (LOCKED). If the cooking zones are
in a "hot" status, the display shows "L" and "H" in
alternation. When the Touch Control is ON it can be
switched-
OFF at any time by operating the ON/OFF key. This is also
valid if the control has been locked (activated child safety
feature).
The ON/OFF key has always priority in the switch-OFF
function.
Automatic switch-OFF
When the control is ON it automatically switches-OFF after
20 seconds if no cooking zone or select key has been
operated within this period of time. If case of a cooking zone
selection, the automatic switch- OFF time is composed of 10
seconds deselection time for a cooking zone at setting"0"
and 10 seconds switch-OFF time.
Switching a cooking zone ON and OFF
First place the pan in the chosen cooking zone. If the pan is
not present the system cannot be switched on the
correspondent zone.
If the touch control is switched on, the cooking zone can be
selected by pressing the button (4) of the corresponding
zone.
The display (5) of the zone selected lights up, while the
remaining displays are dimmed. if the cooking zone is "hot",
"H" and "0" are alternately displayed.
Press the PLUS (3) or MINUS (2) button to select a setting
and the zone will begin to heat up.
Once the cooking zone has been selected, the setting can be
selected by keeping the PLUS (3) button pressed down. The
setting begins at level 1 and increases by 1 level every 0.4
seconds. When setting "9" is reached, the setting will not be
changed further.
If the setting level has been selected using the MINUS (2)
button, the start level is "9" (maximum level). Keep the
button pressed down to lower the active level by 1 every 0.4
seconds. When setting "0" is reached, there will be no
further setting changed. The setting can only be changed by
pressing the MINUS (2) or PLUS (3) button again.
Switching a cooking zone off