Publicidad
Idiomas disponibles
Idiomas disponibles
1 Circular saw blade
1 Blade wrench
1 Parallel fence
1 Dust extraction spout
1 Instruction manual
•
Check for damage to the tool, parts or accessories which may
have occurred during transport.
•
Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The date code
26
, which also includes the year of manufacture,
is printed into the housing.
Example:
2019 XX XX
Year of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Trigger switch
1
Main handle
2
Blade lock
3
End cap
4
Auxiliary handle
5
Bevel adjustment knob
6
Bevel angle adjustment mechanism
7
Base plate
8
Lower blade guard
9
Blade clamping screw
10
Lower guard lever
11
Upper blade guard
12
Lock-off button
13
Intended Use
These heavy-duty circular saws are designed for professional
wood cutting applications. DO nOt use water feed attachments
with this saw. DO nOt use abrasive wheels or blades.
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
These heavy-duty saws are professional power tools.
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Changing Blades
To Install the Blade (Fig. A–D)
CAUTION (DWE550 ONLY): The inner flange has a
20 mm diameter on one side and a 19 mm diameter on
the other. The 19 mm diameter side is marked 19, and
the 20 mm diameter side is marked 20. Use the correct
side for the hole diameter of the blade you intend to use.
Mounting the blade on the wrong side may result in
dangerous vibration.
1. Using the lower guard lever
guard
9
and place blade on saw spindle against the inner
clamp washer
15
, making sure that the blade will rotate
in the proper direction (the direction of the rotation arrow
on the saw blade and the teeth must point in the same
direction as the direction of rotation arrow on the saw). Do
not assume that the printing on the blade will always be
facing you when properly installed. When retracting the
lower blade guard to install the blade, check the condition
and operation of the lower blade guard to assure that it is
working properly. Make sure it moves freely and does not
touch the blade or any other part, in all angles and depths
of cut.
2. Place outer clamp washer
flat surface against the blade and the wording on the outer
clamp washer facing you.
3. Thread blade clamping screw
(screw has right-hand threads and must be turned clockwise
to tighten).
4. Depress the blade lock
3
while turning the saw spindle
with the blade wrench until the blade lock engages and the
blade stops rotating.
5. Tighten the blade clamping screw firmly with the
blade wrench.
nOtE: Never engage the blade lock while saw is running, or
engage in an effort to stop the tool. Never turn the saw on
EngLIsh
, retract the lower blade
11
14
on saw spindle with the large
into saw spindle by hand
10
29
Publicidad
