Ravelli RBV 706 Manual De Uso Y Mantenimiento página 56

Rev.1 14/02/18
Pag.56
EN
Handheld touch radio initialization Handheld touch radio initialization
Handheld touch radio initialization
In order to operate correctly, the handheld set should be interfaced with the electronic board installed inside the stove. For this In order to operate correctly, the handheld set should be interfaced with the electronic board installed inside the stove. For this
Handheld touch radio initialization
In order to operate correctly, the handheld set should be interfaced with the electronic board installed inside the stove. For this
reason, on display appears the following message: reason, on display appears the following message:
If the handheld set is used for the first time, select YES using the selection keys and confirm with the dedicated key. On the display In order to operate correctly, the handheld set should be interfaced with the electronic board installed inside the stove. For this
reason, on display appears the following message:
reason, on display appears the following message:
of the handheld set appears the following:
If the handheld set is used for the first time, select YES using the selection keys and confirm with the dedicated key.
If the handheld set is used for the first time, select YES using the selection keys and confirm with the dedicated key.
If the handheld set is used for the first time, select YES using the selection keys and confirm with the dedicated key.
If the handheld set is used for the first time, select YES using the selection keys and confirm with the dedicated key.
On the display of the handheld set appears the following:
On the display of the handheld set appears the following:
Hold down for a few seconds the button of radio communication (RADIO ADJ) of the PCB, located on the back of the stove, to
On the display of the handheld set appears the following:
On the display of the handheld set appears the following:
initialize the device.
Hold down for a few seconds the button of radio communication (RADIO ADJ) of the PCB, located on the back of the stove, to
Hold down for a few seconds the button of radio communication (RADIO ADJ) of the PCB, located on the back of the stove, to
Hold down for a few seconds the button of radio communication (RADIO ADJ) of the PCB, located on the back of the stove, to
initialize the device.
initialize the device.
Hold down for a few seconds the button of radio communication (RADIO ADJ) of the PCB, located on the back of the stove, to
initialize the device.
initialize the device.
1
2
The flashing yellow LED indicates that the circuit board is waiting to receive the signal from the handheld set.
The flashing yellow LED indicates that the circuit board is waiting to receive the signal from the handheld set.
The flashing yellow LED indicates that the circuit board is waiting to receive the signal from the handheld set.
The flashing yellow LED indicates that the circuit board is waiting to receive the signal from the handheld set.
The flashing yellow LED indicates that the circuit board is waiting to receive the signal from the handheld set.
By pressing the enter key on the handheld set, the components start communicating with each other. A check sign on the display,
By pressing the enter key on the handheld set, the components start communicating with each other. A check sign on the display,
By pressing the enter key on the handheld set, the components start communicating with each other. A check sign on the display, By pressing the enter key on the handheld set, the components start communicating with each other. A check sign on the display,
accompanied by a sound signal, shows that the initialization of the handheld set has been completed sucessfully
accompanied by a sound signal, shows that the initialization of the handheld set has been completed sucessfully
By pressing the enter key on the handheld set, the components start communicating with each other. A check sign on the display,
accompanied by a sound signal, shows that the initialization of the handheld set has been completed sucessfully
accompanied by a sound signal, shows that the initialization of the handheld set has been completed sucessfully
accompanied by a sound signal, shows that the initialization of the handheld set has been completed sucessfully
When you replace the batteries, you do not have to run the initialization procedure of the handheld set. In this case, when
When you replace the batteries, you do not have to run the initialization procedure of the handheld set. In this case, when
When you replace the batteries, you do not have to run the initialization procedure of the handheld set. In this case, when
on display appears the message "FIRST INSTALLATION ?", select NO and press the confirmation key.
on display appears the message "FIRST INSTALLATION ?", select NO and press the confirmation key.
on display appears the message "FIRST INSTALLATION ?", select NO and press the confirmation key.
When you replace the batteries, you do not have to run the initialization procedure of the handheld set. In this case, when
on display appears the message "FIRST INSTALLATION ?", select NO and press the confirmation key.
Description of the display
Description of the display
Description of the display
Description of the display
The display of the handheld set is described below (in stand-by mode):
The display of the handheld set is described below (in stand-by mode):
The display of the handheld set is described below (in stand-by mode):
The display of the handheld set is described below (in stand-by mode): Description of the display
The display of the handheld set is described below (in stand-by mode):
After 5 minutes of inactivity, the display of the handheld set turns dark, switching to "SLEEP" mode, while maintaining the
After 5 minutes of inactivity, the display of the handheld set turns dark, switching to "SLEEP" mode, while maintaining the After 5 minutes of inactivity, the display of the handheld set turns dark, switching to "SLEEP" mode, while maintaining the
radio connection with the stove. By pressing the key ON/OFF, the display becomes active again.
radio connection with the stove. By pressing the key ON/OFF, the display becomes active again. radio connection with the stove. By pressing the key ON/OFF, the display becomes active again.
After 5 minutes of inactivity, the display of the handheld set turns dark, switching to "SLEEP" mode, while maintaining the
radio connection with the stove. By pressing the key ON/OFF, the display becomes active again.
The first pressure of any key with the display active, lights up its backlight, but it is not, however
The first pressure of any key with the display active, lights up its backlight, but it is not, however
The first pressure of any key with the display active, lights up its backlight, but it is not, however
considered a command.
considered a command.
considered a command.
The first pressure of any key with the display active, lights up its backlight, but it is not, however
considered a command.
Use and maintenance manual RBV 706 - RBV 708
User's manual HANDHELD TOUCH RADIO User's manual HANDHELD TOUCH RADIO
User's manual HANDHELD TOUCH RADIO
User's manual HANDHELD TOUCH RADIO
FIRST INSTALLATION?
FIRST INSTALLATION?
FIRST INSTALLATION?
FIRST INSTALLATION?
PRESS THE KEY RADIO
PRESS THE KEY RADIO
PRESS THE KEY RADIO
ADJ ON THE STOVE
ADJ ON THE STOVE
PRESS THE KEY RADIO
ADJ ON THE STOVE
ADJ ON THE STOVE
5
3 4
YES
YES
YES
YES
1
Serial port
2
Handheld cable connection socket
3
ADJ radio: button to connect your handheld to the board
4
Signalling LED
Red: active alarm
Yellow: Waiting communication with the handheld set
Green: Cooker switched on
5
Cooker ON/OFF key
1
1
2
2
3
3
Vers. 01 of:07.04.14
Vers. 01 of:07.04.14
1
1
2
2
3
3
,
,
,
,
Vers. 01 of:07.04.14
Pag.20 Pag.20
Vers. 01 of:07.04.14
Pag.20
Pag.20
.
.
.
.