Publicidad
Idiomas disponibles
Idiomas disponibles
English
•
The blade guard assembly is properly attached and the anti-kickback assembly
is functioning.
ALWAYS inspect the blade guard assembly and riving knife for proper alignment,
•
operation and clearance with saw blade.
ALWAYS make sure both guards are in the down position in contact with the table
•
before operating.
WARNING: To reduce the risk of serious personal injury, have push stick ready to use before
starting cut.
Failure to adhere to these common safety rules can greatly increase the likelihood of injury.
WARNING: Before installing the battery in the table saw or operating the saw, always
inspect the blade guard assembly and riving knife for proper operation alignment and
clearance with saw blade.
WARNING: Ripping or crosscutting may cause saw to tip over while operating. Make sure
saw is securely mounted to a stable surface.
WARNING: Never use the fence and miter gauge together. This may cause a kickback
condition and injure the operator.
CAUTION: If this saw makes an unfamiliar noise or if it vibrates excessively, cease operating
immediately, turn unit off and remove the battery pack until the problem has been located
and corrected. Contact a D
WALT factory service center, a D
e
or other qualified service personnel if the problem cannot be found.
WARNING: The proper throat plate must be in place at all times to reduce the risk of a
thrown workpiece and possible injury.
There are two basic types of cutting with table saws: ripping and crosscutting. Regardless of
material, man made or natural wood, the distinction between ripping and crosscutting is as
follows: Ripping is cutting to a different width (usually with the grain) and crosscutting describes
cutting material across the shorter dimension (usually against the grain).
WARNING: When ripping, always use the fence to provide a guide for the material and
blade guard assembly to protect against a kickback situation.
WARNING: Never perform any cutting operation free hand. Never perform plunge cutting.
WARNING: When crosscutting, aways use the miter gauge. Do not use both the rip fence
and miter gauge together.
Installing and Removing the Battery Pack (Fig. Q)
nOTE: For best results, make sure your battery pack is fully charged.
To install the battery pack
12
into the tool, align the battery pack with the rails inside the tool
and slide it in until the battery pack is firmly seated and ensure that it does not disengage.
To remove the battery pack from the tool, press the release button
pack out of the tool. Insert it into the charger as described in the charger section of this manual.
Fig. Q
On-Off Switch Operation (Fig. R)
WARNING: To reduce the risk of injury, be sure the switch is in the OFF position before
installing the battery.
Lift the red paddle and push green button
Push the red button
49
or push down the red paddle
Locking Off the Saw
The On-Off switch may be locked to prevent unauthorized operation of the saw. To lock the
switch in the Off position, insert a padlock through the red handle and hole
not exceed a maximum diameter of 1/4" (6.35 mm).
10
WALT authorized service center
e
and firmly pull the battery
13
12
13
in to turn this saw on.
48
51
to turn this saw off.
50
. Padlock must
Fig. R
48
49
50
Guard Operating Feature (Fig. S)
WARNING: To reduce the risk of serious personal injury, turn unit off and remove the
battery pack before making any adjustments or removing/installing attachments
or accessories. An accidental start-up can cause injury.
1. The guard arms
52
will lock in place when in the raised position.
2. This feature improves visability when measuring the blade to fence distance.
3. Push down on guard(s) and they will release to the operating position.
nOTE: Pull on the anti-kickback assembly to ensure it is locked in place.
AlWAYs make sure both guards are in the down position in contact with the table
before operating.
Fig. S
Rip Fence Operation (Fig. A, T)
Rail lock lever (Fig. A)
The rail lock lever
5
locks the fence in place preventing movement during cutting. To lock the
rail lever, push it down and toward the rear of the saw. To unlock, pull it up and toward the
front of the saw.
WARNING: When ripping, always lock the rail lock lever.
Work Support Extension/Narrow Ripping Fence (Fig. T)
The table saw is equipped with a narrow ripping fence that also supports work that extends
beyond the saw table.
To use the narrow ripping fence in the work support position, rotate it from its stored position as
shown in Figure T, and slide the pins into the lower sets of slots
To use the narrow ripping fence in the narrow ripping position, snap the pins into the upper sets
of slots
on both ends of the fence.
54
This feature will allow 2" (51 mm) of extra clearance to the blade. Refer to figure T.
Fig. T
54
53
nOTE: When not in use, the narrow ripping fence should be placed in its stored position.
nOTE: This fence will allow the guard to remain on the saw when completing narrow ripping.
This fence will provide ample space for a push stick.
Fine Adjustment Knob (Fig. A)
The fine adjustment knob
allows smaller adjustments when setting the fence. Before adjusting,
4
be sure the rail lock lever is in its up or unlocked position.
51
52
53
on both ends of the fence.
Publicidad
