Publicidad
Idiomas disponibles
Idiomas disponibles
Auxiliary functions
Auxiliary Function Selection Buttons
Select the required auxiliary functions before
starting the program.
C
Some combinations cannot be selected
together. (Ex.: Pre-wash and Quick Wash.
Warning signal on the selected auxiliary function
will light up.
Auxiliary function selection
If an auxiliary function that should not be
selected together with a previously selected
function is chosen, the first selected function
will be cancelled and the last auxiliary function
selection will remain active.
(Ex.: If you want to select pre-wash first and
then quick wash, pre-wash will be cancelled and
quick wash will remain active.
Auxiliary function that is not compatible with the
program cannot be selected. (see, "Program
Selection Table")
C
Auxiliary function buttons may differ
according to the model of your machine.
• Prewash
A pre-wash is only worthwhile for heavily soiled
laundry. Without pre-wash you save energy,
water, detergent and time.
C
Pre-wash without detergent is recommended
for lace and curtains.
• Quick Wash
This function can be used for "Cottons" and
"Synthetics" programs. It decreases the washing
times for lightly soiled laundries and also the
number of rinsing steps.
• Rinse Plus
With this function, you can increase the number
of current rinsing steps. Thus, sensitive skins'
risk of being affected by the remainder detergent
on the clothes will be decreased.
• Anti-Creasing
With this function, drum movement will be
lessened to prevent creasing and spinning speed
is limited. In addition, washing is carried out at a
higher water level.
C
Whenever you select this auxiliary function,
load your machine with half of the maximum
laundry specified in the program table.
• No Heat
If you wish to wash your clothes in cold water,
you can use this program.
Starting the Program
1. Press "Start/Pause/Cancel" button to start the
program.
2. Program follow-up lamp showing the startup
of the program will light up.
Progress of program
Progress of a running program is shown through
the program follow-up indicator. At the beginning
of every program step, the relevant indicator
lamp will light up and light of the completed step
will turn off. The symbol that is lit up at the far
right of the series of symbols indicates the step
that is being carried out.
C
If the machine is not spinning, the program
may be in rinse hold mode or the automatic
spin correction system has been activated
due to an excessive unbalanced distribution
of laundry in the machine.
Changing the selections after the
program has started
Turning the program knob while the program is
in a normal flow will not change the program.
Switching the machine to standby mode
Press "Start/Pause/Cancel" button momentarily
to switch your machine to the standby mode.
Auxiliary functions can be cancelled or selected
in accordance with the step the program is at.
The door can be opened if the water level is
suitable. Laundry may be added / taken out by
opening the door.
Door lock
The loading door can not be opened yet due
to safety reasons while the "Ready" lamp is
flashing. The loading door can be opened once
the "Ready" lamp starts lighting up continuously.
Child-proof lock
You can protect the appliance from being
tampered by children by means of the child-
proof lock. In this case, no change can be made
in the running program.
This function protects the appliance from being
tampered by children. In this case, all of the
buttons are inactive except On/Off button; by
On/Off button you can whether stop or resume
(while child-lock on) the program of your
machine.
The machine is switched to child-lock by
pressing the 1st and 2nd auxiliary functions from
the left for 3 sec. 1st auxiliary function light will
flash continuously. To deactivate the child-proof
lock, press the same buttons for 3 sec.
Ending the program through
canceling
"Start/Pause/Cancel" button is pressed for
3 seconds to cancel the program. "Ready"
warning lamp flashes during canceling and "End"
will appear on the display.
8 - EN
Publicidad
