Publicidad
Idiomas disponibles
Idiomas disponibles
LUBRICATION
IMPORTANT: The chain saw is
not supplied filled with oil. It is
essential to fill with oil before use.
Never operate the chain saw without
chain oil or at an empty oil tank level, as
this will result in extensive damage to
the product.
Filling oil tank:
WARNING: Unplug chain saw from
power source before filling the oil
tank.
1. Set chain saw on any suitable surface with
Oil Filler Cap (5) facing upward.
2. Clean area around the Oil Filler Cap with
cloth and unscrew the cap by turning it
counter clockwise.
3. Add bar and chain oil until reservoir is full.
4. Avoid dirt or debris entering oil tank, refit
Oil Filler Cap (5) and tighten by turning
clockwise until hand tight.
IMPORTANT: To allow venting of
the oil reservoir, small breather
channels are provided between the Oil
Filler Cap and the strainer, to prevent
leakage ensure machine is left in a
horizontal position (Oil Filler Cap (5)
14
uppermost) when not in use.
It is important to use only the
recommended standard bar and chain
oil (Grade: ISO VG32) to avoid damage
to the chain saw.This can be found at
the location you purchased this saw or
your local hardware store. Never use
recycled/old oil. Use of non approved oil
will void the warranty
Oiling chain
Always check oil level before using saw. Do
not attempt to operate the oil system while
saw is in operation. To oil chain, press the
Bulb (23). Oil will feed through the Oil Outlet
(17) onto the Guide Bar (9) and chain. Press
the Bulb (23) on Oil Filler Cap at least once
before each cut (see Fig. F)
OPERATION
1. SWITCHING ON AND OFF (See Fig. G)
ATTENTION: Check the voltage and
current supply: The voltage and
Electric Chain Saw
current supply must comply with the
ratings on the product plate.
For switching on the tool, press the Lock-
Out Button (3), then fully press the On/Off
Switch (2) and hold in this position. The Lock-
Out Button can now be released.
For switching off, release the On/Off Switch .
2. CUTTING
IMPORTANT: Is the oil reservoir
filled? Check the Oil Level Window
(4) prior to starting and regularly during
operation.(See Fig. H1) Refill oil when
oil level is low. A full oil tank will last
approx. 12 minutes of cutting depending
on sawing intensity and stops. Check
recent replaced chain tension about
every 10 minutes during operation.
1) Connect saw to extension cord. Connect
extension cord to power supply.
(See Fig. H2 )
2) Make sure section of log to be cut is not
laying on the ground. This will keep the
chain (10) from touching the ground as it
cuts through the log.
Touching the ground while the Chain is
moving is dangerous and will dull the
Chain.
3) Use both hands to grip saw. Always use
left hand to grip Front Handle (6) and
right hand to grip Rear Handle (1). Use a
firm grip. Thumbs and fingers must wrap
around saw handles. (See Fig.H3 )
4) Make sure your footing is firm. Keep feet
shoulder width apart. Distribute your
weight evenly on both feet.
5) When ready to make a cut, push the
Lock-Out Button (3) completely in with the
right thumb and squeeze the trigger. This
will turn the saw on. Releasing the trigger
will turn the saw off. Make sure the saw is
running at full speed before starting a cut.
6) When starting a cut, slowly place moving
chain against the wood. The wood should
be as close to the saw body as possible.
Hold saw firmly in place to avoid possible
bouncing or skating (sideways movement)
of saw.
7) Guide the saw using light pressure and
do not put excessive force on the saw,
letting the saw do its work. The motor will
overload and can burn out. It will do the
job better and safer at the rate for which it
was intended.
EN
Publicidad
