Kärcher BRC 50 W Bp Manual Del Usuario página 16

Set key switch to "0" with the cleaning
head raised.
Unscrew the knurled-head screw.
Remove the vacuum bar.
Pull out the suction hose from the vacu-
um bar.
Rinse the vacuum bar from the top with
water.
Obstructions in the gap between the
slide shoes can be removed with a spat-
ula. If necessary, the slide shoes can be
unscrewed from the vacuum bar for
cleaning.
Repeat the cleaning process on the
second vacuum bar.
Reattach both vacuum bars to the appli-
ance in reverse sequence.
Cleaning the floater
1 Sieve with floater ball
2 Pipe
Fault Remedy
Appliance cannot be Insert the battery plug on the device.
started
Release emergency-stop button by turning.
If battery is low, charge the battery.
Check battery cable for correct sitting.
Check battery cable for corrosion; clean, if required.
Device does not drive Reset fuse of traction drive
or drives only slowly
If battery is low, charge the battery.
The appliance was switched on while a drive key was pressed. Release the drive switch.
Control system overheated; switch off device and let it cool down.
Insufficient vacuum Empty the dirt water reservoir.
performance
Clean the seals between dirt water reservoir and cover and check for tightness, replace if required.
Check suction hose for blockages; clean if required.
Check connection between suction hose and vacuum bar and suction hose and the device.
Check the suction hose for tightness; replace if required.
Check if the cover on the dirt water discharge hose is closed
Clean the floater in the dirt water tank.
Reset fuse of suction turbine.
Insufficient cleaning re- Check the brushes for wear, replace if required.
sult
Check brushes for wear and tear, clean.
If battery is low, charge the battery.
Brushes are rotating Reset fuse of brush drive.
slowly or not at all
Check the brushes for blockage due to foreign particles, remove them if found.
If battery is low, charge the battery.
No or very little deter- Check level of detergent solution in the fresh water tank; refill, if required.
gent solution gets add-
Turn on the key Apply detergent solution - the control lamp must illuminate.
ed
Check nozzles for blockages; clean if required.
Check fresh water filter; clean if required.
Do not add detergents Refill detergent tank.
Press the ventilation switch for the respective tank for 30 seconds.
Flush the pipe system for the detergent with water.
The cleaning head can- Reset fuse of control system.
not be raised/lowered
16 English
Clean the sieve from the outside and
rinse it.
Check the mobility of the floater ball.
If it is too dirty:
Hold the pipe firmly and pull out the
sieve from the pipe.
Clean sieve and ball.
Hold the pipe firmly and reinsert the
sieve.
Lubricating the drive axle and the steer-
ing rollers
Lubricate the greasing nipple with a
grease press.
Frost protection
In case of danger of frost:
Empty the fresh and dirt water reser-
voirs.
Store the appliance in a frost-protected
room.
Transport
Danger
Risk of injury! When loading or unloading
the machine, it may only be operated on
gradients of max. 2%. Drive slowly.
Warning
Danger of damage to the control. The appli-
ance should only be operated with the drive
motor removed. The pushing speed must
not exceed 8 km/h.
Remove the vacuum bar and lift up the
cleaning head prior to loading the appli-
ance via a ramp.
If you want to transport the machine on
a vehicle secure it from slipping using
belts/ ropes.
Secure the wheels of the machine with
wheel chocks.
Faults
Danger
Risk of injury! Before carrying out any tasks
on the machine, set the main key to "0" and
remove it. Pull out the battery plug.
Drain and dispose of the dirt water and
the residual fresh water.
In case of faults that cannot be remedied
using the table below please contact the
By whom
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator