RIB JOLLY 20 3P FAST Manual De Instrucciones página 16

G
TECHNICAL DATA / INSTALLATION JOLLY
B
TECHNICAL DATA
Max gate weight
Max gate surface
Limit switch winding capacity
Max operating torque with J-INV 3P control board
Max operating force with J-INV 3P control board
Pulley revolutions
Pulley diameter
Shaft diameter
EEC Power supply
Motor capacity with load
Power absorbed with load
Functioning cycles with J-INV 3P control board
Daily operations suggested with J-INV 3P control board
Service with J-INV 3P control board
Nominal functioning time with J-INV 3P control board
Motor weight
Working Temperature
Protection
*
*
JOLLY 20 Ø 200 / 7,8
JOLLY 22 Ø 220 / 8,6
ROLLING GATE CONTROL
The European Standard EN 12604 "Industrial, Commercial and Garage Doors and Gates -
Mechanical Aspects - Requirements", at the point 4.3. "Protection against unintentional and
uncontrolled movements" requires also that*:
a - The vertically operating door leaves shall be balanced so that the door leaf can stop in
any position, or that the out-of-balance state shall not produce, in any case, a static
force at the primary closing edge of the door exceeding 150N (15,3 kg / 33,70 lbs).
Verify it after having manually released the JOLLY operator.
b - If a spring fails, the resulting out-of-balance static force occurring at the primary
closing edge of the roller shutter shall not exceed 200N (20,4 kg / 44,94 lbs), even
when the Jolly operator is manually released. After this failure, you must intervene on
the door to substitute the broken spring and correct the balance state. Therefore, we
suggest you to fraction the roller shutter weight with an adequate number of springs
(* This is a free interpretation).
WARNING: The EN 12453 standard "Industrial, commercial and garage doors and gates
- safety in use of power operated doors - test methods" at point 6.2.2 "safeguarding
against hazard of being lifted" provides that the rolling gate shall not be able to lift more
than 20 kg / 44 lbs. In order to meet this standard, RIB suggests to install the control
board with electric power regulation J-INV 3P (cod. ABJ0012).
kg/lbs
2
m
N. rotat.
Nm
kg/lbs
rpm
mm/in
mm/in
W
A
N.
N.
%
s
kg/lbs
°C
IP
326 / 12,8 41 / 1,6
**
**
JOLLY 20 ø 48 / 1,9
JOLLY 22 ø 60 / 2,3
Measurements in mm/inch
JOLLY 20 3P FAST JOLLY 22 3P FAST
220/485
16
9,5
110
110/242
11
200/7,8
48/1,8
230V 3~ 50/60Hz
480
1,2
100 - 20s/2s
20
30
330
8,5/18,7
-10 ÷ +70
30
Parts to install according to EN 12453 standard
COMMAND TYPE
(out of public area*)
Hold-to-run operation
Impulsive - in sight
(e.g. push-button)
impulsive - out of sight
(e.g. remote)
automatic
* a typical example are those doors which do not have access to any public way
A: Hold-to-run operation made by push-button ex: code ACG2013
B: Hold-to-run operation made by key selector ex: code ACG1010
C: Adjustable power of the motor or photocells to respect impact forces as indicated in
Annex A
D: Safety strips and/or other additional devices to reduce the probability of contact with
the door.
E: Devices installed in such a way that a person can not be touched by the door.
IN ORDER TO ENSURE A CORRECT FUNCTION ONLY RIB'S
COMPONENTS MUST BE USED
1 - JOLLY operator
2 - Photoelectric cells (external)
3 - Push-Button
16
8,5
120
110/242
10
220/8,6
60/2,3
9,5/20,9
USE OF THE SHUTTER
Skilled persons Skilled persons
(public area)
A B
C or E C or E
C or E C and D, or E
C and D, or E C and D, or E
4 - Key selector
5 - Tuned aerial
6 - Flashing lamp
Not skilled
persons
Not possible
C and D, or E
C and D, or E
C and D, or E