Setting Into Operation; Automatic Mode; Music Mode - IMG STAGELINE FLOWER LED-340RGBW Manual De Instrucciones

For suspended mounting tightly screw the unit via
the bracket (1) to a suitable place, e. g. to a cross
bar or a lighting stand. To align the unit, release the
locking screws (6). Adjust the desired inclination of
the unit and retighten the screws.
WARNING Mount the light effect unit safely and
expertly. If the unit is installed at a
place where people may walk or sit
under it, additionally secure it, e. g. by
a safety rope. Lead the safety rope
through the safety lug (2) and fix it so
that the maximum falling distance of
the unit will not exceed 20 cm.

5 Setting into Operation

WARNING Never look directly into the light
source, this may cause eye damage.
Please note that stroboscope effects
and fast changes in lighting may trig-
ger epileptic seizures with photosensi-
tive persons or persons with epilepsy!
Connect the mains cable supplied to the mains jack
(9) and the plug to a socket (230 V~ / 50 Hz). Thus,
the unit is switched on. To switch off the unit, dis-
connect the mains plug.
For a more convenient operation, it is recom-
mended to connect the unit to a socket which can
be switched on and off via a light switch.
Caution: Do not connect the unit to the mains volt-
age via a dimmer!
6 Operation without Controller
Via the DIP switch block (5) the light effect unit may
be adjusted to different operating modes.

6.1 Automatic mode

If the automatic mode has been adjusted, a light
show will run automatically. To adjust this mode, set
the DIP switches No. 10 and No. 8 to ON (upper
position).
Fig. 3
Setting the automatic mode

6.2 Music mode

If the music mode has been adjusted and music is
played with a clear rhythm in the bass range, the
run of the light effects is synchronized to the rhythm
of the music via the integrated microphone (4). To
adjust this mode, set the DIP switches No. 10 and
No. 7 to ON (upper position).
Fig. 4
Setting the music mode
Advance the control (3) for the microphone sensi-
tivity so far clockwise until the unit responds to the
music as desired. When changing the volume at
the music system, also the microphone sensitivity
must be adapted accordingly.
6.3 Mode "Full Light"
In the mode "Full Light" all LEDs light up. To adjust
this mode, set the DIP switches No. 10 and No. 6 to
ON (upper position).
Fig. 5
Setting the mode "Full Light"
6.4 Running light modes "Run 1" to "Run 3"
The unit may be set to three different running light
modes "Run 1" to "Run 3".
To adjust "Run 1", set the DIP switches No. 10 and
No. 5 to ON (upper position).
Fig. 6
Setting "Run 1"
To adjust "Run 2", set the DIP switches No. 10 and
No. 4 to ON (upper position).
Fig. 7
Setting "Run 2"
To adjust "Run 3", set the DIP switches No. 10 and
No. 3 to ON (upper position).
Fig. 8
Setting "Run 3"
Note: The three running light modes correspond to the run-
ning light programmes which can be called when the DMX
control is used ( table, chapter 9.1):
"Run 1" same as mode 3,
"Run 2" same as mode 1,
"Run 3" same as mode 2.
6.5 Increasing the speed
For the automatic mode (chapter 6.1) and the three
running light modes (chapter 6.4) the running light
speed can be increased in several steps via the
DIP switches No. 1 and No. 2. Adjust the switches
according to the desired speed.
min.
Fig. 9 Increasing the speed
GB
max.
9