Fimap FSM Manual De Uso página 11

At the end of the work, and before carrying out any type of maintenance, perform the following operations:
1. Take the device to the dedicated maintenance area.
2. Clean the appliance with a damp cloth.
ATTENTION: do not leave the appliance exposed to the sun for long periods.
3. Put the appliance in rest mode.
4. Remove any debris in the side brushes and in the central brush (Fig.1).
5. Check the state of wear of the central brush, and if necessary change it.
ATTENTION: to change the brush, remove the fastening screws (Fig.2).
6. Clean the front flap with a damp cloth (Fig.3).
7. Check the state of wear of the front flap, and if necessary change it.
ATTENTION: to change the flap, remove the fastening screws.
8. Clean the rear flap with a damp cloth (Fig.4).
9. Check the state of wear of the rear flap, and if necessary change it.
ATTENTION: to change the flap, remove the fastening screws.
10. Clean the side flaps with a damp cloth (Fig.5).
11. Check the state of wear of the side flaps, and if necessary change them.
ATTENTION: to change the flap, remove the fastening screws.
12. Make sure the pivoting wheels are fixed correctly (Fig.6).
ATTENTION: for this operation use the equipment supplied with the appliance
13. Clean the rear wheels with a damp cloth.
14. Check the state of wear of the wheels, and if necessary change them.
ATTENTION: to change the rear wheel, remove the wheel cover (Fig.7), using a suitable tool
remove the nuts and bolts fixing the rear wheel to the frame (Fig.8), replace the old wheel with the
new one.
ATTENTION: whenever the rear wheels are changed also change the nuts and bolts.
15. Check the condition of the drive belt, and if necessary change it.
ATTENTION: check the rotation of the side brush, if the appliance is moving forward the side brush
should rotate towards the inside of the appliance (Fig.9).
10076791-AA_UM_FSM-ID.indb 11
MAINTENANCE
1
3
5 6
7
9
TYPE OF MAINTENANCE
Check the condition of the central brush.
Check the condition of the side brush.
Adjusting the position of the central brush with respect to the ground.
Adjusting the position of the side brush with respect to the ground.
Checking the front flap.
Checking the rear flap.
Checking the side flap.
2
Checking the condition of the drive belt
Checking the gears and pulleys
This chapter lists the most common problems linked with the use of the appliance. If you are unable to
resolve the problems with the information given here, please contact your nearest assistance centre.
PROBLEM POSSIBLE CAUSE
The debris hopper is full.
The central brush is not touching
the floor.
The side brush is not touching the
THE APPLIANCE floor.
DOES NOT CLEAN
CORRECTLY
4
Excessive wear of the central brush.
Excessive wear of the side brush.
Excessive wear of the side brush
drive belt.
The debris hopper is full.
TOO MUCH DUST
COMING OUT Rear filters clogged.
WHEN WORKING
Worn or damaged flaps
To dispose of the appliance, take it to a demolition centre or an authorised
collection centre.
Before scrapping the appliance, it is necessary to remove and separate out
the following materials, then send them to the appropriate collection centres in
accordance with applicable environmental hygiene regulations:
• Brushes
• Plastic parts
• Metallic parts
8
11
X
X
X
X
TROUBLESHOOTING
SOLUTION
Empty the debris hopper.
Adjust the central brush (move the
knob towards the symbol "+").
Adjust the side brush (move the knob
towards the symbol "+").
Change the central brush.
Change the side brush.
Change the side brush drive belt.
Empty the debris hopper.
Clean the rear filters.
Replace the worn or damaged flaps.
DISPOSAL
X
X
X
X
X
21/02/2018 08:54:13