Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATING YOUR FURNACE
For your SAFETY, read before
LIGHTING
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
A.
This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these
Instructions exactly.
BEFORE LIGHTING smell around the appliance area
B.
for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance or strike a match.
• Do not touch any electric switch; do not use any
phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call the fire
department.
C.
Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it, call a qualified
service technician. Force or attempted repair may
result in a fire or explosion.
D.
Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
IMPORTANT: KEEP BURNER AND CONTROL
COMPARTMENT CLEAN. Make sure the "FOR YOUR SAFETY"
hang tag (see below) hangs below the heat shield.
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition
device which automatically lights the pilot.
B. BEFORE LIGHTING smell all around the
appliance area for gas. Be sure to smell next
to the floor because some gas is heavier
than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance or strike a
match.
Do not touch any electric switch; do not use
any phone in your building.
Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
OPERATING INSTRUCTIONS
STOP! Read the safety information above.
1.
2. Turn off all electric power to the appliance
(if applicable).
3. Set the thermostat to lowest setting.
4. Open control access panel.
5. This appliance is equipped with an ignition
device which automatically lights the pilot.
Do not try to light the pilot by hand.
6. Turn the gas control knob clockwish
to "OFF".
GAS CONTROL KNOB SHOWN
IN "OFF" POSITION
7.
Wait (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you
then smell gas, STOP! Follow "B" in the safety
information above. If you don't smell gas, go to
the next step.
8. Turn the gas control knob counter clockwise
to "ON".
TO TURN OFF GAS TO APPLIANCE
1.
Set the thermostat to lowest setting.
2. Turn off all electric power to the appliance
if service is to be performed (if applicable).
3. Open the control access panel.
LIGHTING PILOT: (If furnace is equipped with a
manual spark igniter follow next steps).
1.
Review all operating instructions above.
2. When lighting pilot, depress red button
located on the lower right side of the burner
compartment (view pilot through glass
observation door, repeat several times if
necessary).
3. If pilot fails to light or spark is not present
while actuating, follow steps 5 thru 10 above.
Read owner's manual before using / installing. Be sure CHAINED LIGHTING INSTRUCTION
HANGS at the lowest position in the furnace under/below the heat shield.
NOTE: FOR ADDITIONAL INFORMATION REFER TO THE
INSTALLATION AND OPERATION INSTRUCTION MANUAL
SUPPLIED WITH THIS APPLIANCE OR CONTACT THE
250 West Laurel Street · Colton, CA 92324
MANUFACTURER IDENTIFYING THE PRODUCT BY ITS
MODEL NUMBER LOCATED ON THE RATING PLATE,
FOUND NEAR THE GAS VALVE.
Lighting Instructions
STOP! Read the safety information above.
1.
2.
Set the thermostat to lowest setting.
3.
Turn off all electric power to the appliance.
4.
Remove control access panel.
5.
Turn gas control knob clockwise to "OFF".
COUNTERFLOW TOP VENT GAS WALL HEATER
If you cannot reach your as supplier, call
the fire department.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will
not push in or turn by hand, don't try to repair
it, call a qualified service technician. Force
or attempted repair may result in a fire or
explosion.
D. Do not use this appliance if any part has been
under water. Immediately call a qualified service
technician to inspect the appliance and to
replace any part of the control system and
any gas control which has been under water.
9. Close control access panel.
10. Turn on all electric power to the appliance
(if applicable).
11. Turn thermostat to on (HEAT) position. Set
thermostat higher than room temperature.
Pilot will automatically light and main burner(s)
will light in approximately 45 seconds.
NOTE: On initial start-up or after prolonged
shutdown, several ignition cycles may be
required to purge gas lines of air. To accomplish
the recycles - repeat steps 6 thru 11 until pilot is
established.
12. Set thermostat to desired setting.
13. After the room thermostat turns the system
off, a dely of approximately one minute is
required before the system can be turned
on again.
14. If the appliance will not operate, follow the
instructions "TO TURN OFF GAS TO APPLIANCE"
and call your service technician or gas
supplier.
4. Turn gas control knob clockwise
to OFF. Do not force.
5. Close the control access panel
WARING - Do not store or use gasoline or other
flammable liquids or vapors near the furnace.
WARING - Danger of ignition flash and eye
injury or blindness. Protect your eyes. Never at-
tempt to light pilot with gas control valve knob
in "ON" position. Flashback could occur.
WARNING - The surface of the furnace is hot
during operation. Keep children, clothing, furni-
ture and flammable material away.
P323204 RV1-20
23
Publicidad
