Rotary control
The rotary control is used for function selection or switching
off (Sleep mode).
Turn:
Select the Function/Temperature/Timer.
Push - short:
Confirm the selection.
Push - two seconds:
1 x: return to stand-by mode to change a function
2 x: return to sleep mode
Rotary control - light ring
The light ring indicates the current operating mode:
No light:
The unit is in sleep mode.
Blue light:
The unit is in stand-by mode.
Flashing:
The grill rack has not yet reached the selected temperature.
The unit is heating up or cooling down.
Steady:
The selected temperature has been reached.
Orange:
Grilling at 80-350 °C
Red:
Boost-zone 330-500 °C
Purple:
Indirect grilling at 80-200 °C
Timer
The timer is used to monitor the grilling time. It can be set
from 1 min to 23 h 59 mins. Beep signals indicate that the
running time has elapsed; the heating element remains
switched on.
∙ Turn the rotary control until
∙ P ress the rotary control briefly and turn to select the
hours.
∙ P ress the rotary control briefly and adjust the minutes.
∙ C onfirm the time setting by briefly pressing the control.
The colon starts flashing; once the time has elapsed,
beep signals are heard.
∙ To return to stand-by mode, press the rotary control for
two seconds.
∙ Alternatively, set the timer to 0:00, and press the control
briefly to return to stand-by mode.
∙ If the heating is switched off after the timer is set, the
appliance will change to sleep-mode 5 minutes after the
last input, i.e. the timer is switched off.
∙ If the timer is set with the heating already off, it will
continue until the pre-selected time is reached, when the
unit changes to sleep-mode.
Grilling at 80-350°C
To grill sausages, poultry, fish etc. For finishing or keeping
warm steaks.
The entire grill surface is heated.
∙ Turn the rotary control until
∙ P ress the rotary control briefly and turn to select the
14
lights up.
lights up.
desired temperature. Press briefly to confirm.
∙ T he ring starts flashing orange and the appliance is
heating up.
∙ Once the selected temperature has been reached, the
ring shows steady orange.
∙ Place the food on the grill surface.
∙ Close the cover, if desired.
'Boost-zone' grilling 330-500 °C
For searing or light grilling of steaks.
The boost-zone is located to the right; the left side is
heated to 330 °C.
∙ Turn the rotary control until
∙ P ress the rotary control briefly and turn to select the
desired temperature. Press briefly to confirm.
∙ T he ring starts flashing red and the appliance is heating
up.
∙ Once the selected temperature has been reached, the
ring shows steady red.
∙ Place the food on the boost-zone.
Note:
Do not close the cover during Boost-zone grilling. The
Boost-zone function is automatically de-activated when
the cover is closed.
∙ For subsequent cooking, lower the temperature or shift
the food to the left on the grill surface.
Indirect grilling at 80-200°C
For slow cooking, e.g. for roasts or for large steaks that
require additional cooking. This means that only the outer
area of the grilling surface is heated, creating an indirect
grilling zone.
∙ Turn the control dial until
∙ Press the control dial briefly and turn it to set the
required temperature. Confirm by pressing briefly.
∙ The ring flashes purple and the appliance heats up.
∙ As soon as it reaches the selected temperature, the ring
lights up purple continuously.
∙ Place the food on the grilling surface.
∙ Now you can close the lid if you wish.
Grilling with the core thermometer
∙ Scope of supply: 2 items
Other core thermometers are available under item no.
8126.
∙ Caution: The core thermometers heat up during use.
Use suitable protection, eg barbecue gloves.
∙ Fit the thermometer plugs into the sockets at the lower
left of the junction box . To prevent the appliance from
switching off, ensure that the box is not lifted up and
stays properly connected.
∙ Select the desired grill function and temperature.
∙ Once pre-heating is complete and the ring shows a
steady light, put on the food.
∙ Push the tips of the thermometers into the centre of the
food.
∙ U se the rotary control to set the desired core
lights up.
lights up.