Bosch PowerPack 300 Instrucciones De Servicio Originales página 16

English – 4
Inserting and removing the rack-mounted battery (see
figure B)
In order for the battery to be inserted, the key (5) must be
inserted into the lock (6) and the lock must be open.
To insert the rack-mounted battery (2), slide it contacts-
first into the holder (1) on the rack until you hear it click into
place.
Always secure the battery by closing the lock (6) – other-
wise the lock may open and the battery may fall out of the
holder.
Always remove the key (5) from the lock (6) after closing it.
This prevents both the key from falling out and the eBike bat-
tery from being removed by unauthorised third parties when
the eBike is not in use.
To remove the rack-mounted battery (2), switch it off and
open the lock using the key (5). Pull the battery out of the
holder (1).
Removing the PowerTube battery (pivot) (see figure C)
❶ To remove the PowerTube battery (15), open the bat-
tery lock (6) using the key (5). The battery will be un-
locked and fall into the safety restraint (14).
Note: When removing the eBike battery, hold it firmly in your
hand.
❷ Hold the battery firmly and press on the safety re-
straint (14) from above. The battery will be unlocked
completely and fall into your hand. Then pull the bat-
tery out of the frame.
Note: As a result of varying designs, the battery may need
to be inserted and removed using a different method. Read
the operating instructions of the eBike manufacturer.
Inserting the PowerTube battery (pivot) (see figure D)
In order for the battery to be inserted, the key (5) must be
inserted into the battery lock (6) and the battery lock must
be open.
❶ To insert the PowerTube battery (15), place it so that
its contacts are in the lower holder of the frame.
❷ Twist the battery upwards until it is held by the safety
restraint (14).
❸ Hold the battery lock open with the key and press the
battery upwards until you hear it click into place.
❹ Always secure the battery by closing the battery
lock (6) – otherwise the battery lock may open and the
battery may fall out of the holder.
Always remove the key (5) from the battery lock (6) after
locking it. This prevents both the key from falling out and the
eBike battery from being removed by unauthorised third
parties when the eBike is not in use.
Operation
Start-up
Use only original Bosch eBike batteries that the manu-
u
facturer has approved for your eBike. Using other
eBike batteries can lead to injuries and pose a fire hazard.
0 275 007 XPX | (29.05.2023)
Bosch accepts no liability or warranty claims if other
eBike batteries are used.
Switching on/off
Switching on the eBike battery is one way to switch on the
eBike. Read and follow the instructions in the operating
manuals for the drive unit and on-board computer.
Before switching on the eBike battery, i.e. the eBike, make
sure that the battery lock (6) is locked.
To switch on the eBike battery, press the on/off button (4).
Do not use any sharp or pointed objects to press the button.
The LEDs on the indicator (3) will light up, indicating the bat-
tery's state of charge at the same time.
Note: If the eBike battery capacity is less than 5%, none of
the LEDs on the battery charge indicator (3) will light up.
Whether the eBike is switched on can only be determined
from the on-board computer/control unit.
To switch off the eBike battery, press the on/off button (4)
again. The LEDs on the indicator (3) will go out. This will also
switch the eBike off.
If no power is drawn from the drive for about 10 minutes
(e.g. because the eBike is not moving) and no button is
pressed on the on-board computer or the operating unit of
the eBike, the eBike will switch off automatically.
The eBike battery is protected against deep discharge, over-
loading, overheating and short-circuiting by the "Electronic
Cell Protection (ECP)". In the event of danger, a protective
circuit switches the eBike battery off automatically.
Recommendations for Optimal Handling of the
eBike Battery
The service life of the eBike battery can be extended if it is
looked after well and especially if it is stored at the correct
temperature.
As it ages, however, the capacity of the eBike battery will di-
minish, even with good care.
A significantly reduced operating time after charging indic-
ates that the eBike battery has deteriorated. The eBike bat-
tery should be replaced.
Recharging the eBike Battery Before and During Storage
When you are not going to use the eBike battery for an exten-
ded period (longer than three months), store it at a state of
charge of around 30 % to 60 % (when two to three of the
LEDs on the battery charge indicator (3) are lit).
Check the state of charge after six months. If only one of the
LEDs on the battery charge indicator (3) is lit, charge the
eBike battery back up to around 30 % to 60 %.
Note: If the eBike battery is stored with no charge for an ex-
tended period of time, it may become damaged despite the
If a fault is detected in the
eBike battery, two of the
LEDs on the battery charge
indicator (3) will flash. Con-
tact an authorised bicycle
dealer if this happens.
Bosch eBike Systems