Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
1.
Wooden ceiling. Fig. 3
2.
Concrete ceiling. Fig. 4
To assemble the ceiling fan, follow the steps below (Fig. 3-9):
1.
Follow the instructions in the installation section to install the mounting bracket
according to ceiling type.
Then, screw the main body to the mounting bracket as shown in Figure 5.
2.
3.
Take the receiver and make the electrical connections by means of quick connectors. Once
connections are made, insert the receiver inside the upper part of the fan main body.
Follow the wiring instructions shown in Figure 6.
Once the electrical connections have been made, you must install the decorative cover as
4.
shown in the first part of Figure 7 by screwing it onto the mounting bracket.
5.
To install the blades, use the screws and washers supplied in the installation kit. Install
the blade making sure the pointed end faces downwards. Align the blade with the holes
on the underside of the main body and insert the screws. Repeat this step until all blades
are installed. Fig. 7
6.
Finally, take the decorative cover and screw it on as shown in Figure 8.
Warning:
Self-tapping screws are only suitable for wooden ceilings. In case of installing the ceiling fan
to concrete ceilings or joists, use a drill for making the holes and plugs or expansion screws
(not included).
4. OPERATION
Remote control Fig. 9
1.
Power button
Speed control
2.
3.
Winter function
4.
Summer function
5.
Natural Breeze
Natural Breeze shut-off
6.
7.
Timer
Use the 6 speed buttons to select the air power level.
-
-
Press the power button to turn the device off.
-
Use the 3 timer buttons to select the fan's operation time: 1, 2, or 4 hrs. The fan will turn off
once the selected time has elapsed.
44
ENERGYSILENCE AERO 5400 AQUA CONNECTED
-
Press the light button to turn the fan's lamp on and off.
-
The remote control requires 2 x 1.5 V-3AAA batteries.
Winter function: press button 3 for the fan to make air flow from the bottom upwards, bringing
cold air to the top of the room.
Summer function: press button 4 for the fan to make air flow from the top downwards,
bringing cold air to the bottom of the room.
Natural Breeze: activate this mode by pressing the corresponding button on the remote
control. The fan will run at different power levels in a cycle, producing a feeling of fresh air.
Warning:
Invert the spinning direction of the fan while in operation. Hold down the button for approx. 3
seconds, the device will beep, and the blades will start slowing down until they practically stop
spinning. After a few seconds, they will start spinning again in the opposite direction.
Pairing the remote control with the fan: press the power button for 5 seconds until you hear
a beep.
Wi-Fi connection: press the 1h and 4h button simultaneously for 5 seconds until you hear a
beep. Follow the instructions in section 5. Wi-Fi connectivity and mobile App.
Warnings:
-
The remote control operates through RF Wireless digital transmission technology. If both
the fan and the lamp are equipped with a switch, turn on the fan at top speed and turn the
light on before using the remote control.
-
If the fan or the light cannot be controlled through the remote control, check if the batteries
in the remote control are in good conditions and if they make good contact, that the positive
and negative electrodes are in the correct position, and if the batteries are charged.
If the fan or the light cannot be controlled through the remote control, check if there are
-
other remote-controlled products in the same area and check if the transmitter buttons
are pressed. Product with similar remote-control systems may cause interference. This
does not include infrared remote controls.
Pay attention to the product voltage. Too low a voltage may cause the remote control to
-
not work. The technical specifications are indicated in this manual.
-
If the remote control is not going to be used for a long time, remove the batteries.
ENGLISH
ENERGYSILENCE AERO 5400 AQUA CONNECTED
45
Publicidad
