Bosch UniversalImpact 18 Manual Original página 13

Cordless Drill/Driver
Rated voltage
A)
No-load speed
– First gear
– Second gear
A)
Impact rate
Max. torque, hard/soft
screwdriving application ac-
A)
cording to ISO 5393
st nd
Max. drilling diameter (1 /2 Gear)
– Steel
– Wood
Max. screw diameter
Tool holder
Max. impact drilling diameter
Weight according to
B)
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
C)
ure during operation and
during storage
Recommended rechargeable
batteries
D)
Recommended chargers
A) Measured at 20–25 °C with rechargeable battery PBA 18V
1.5Ah.
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
D) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
Noise/vibration information
Noise emission values determined according to
EN 62841-2-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 86 dB(A); sound power level
97 dB(A). Uncertainty K = 5 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-1:
2
Drilling into metal: a <2.5 m/s , K = 1.5 m/s
h
2
Impact drilling: a = 18 m/s , K = 3 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
Bosch Power Tools
plication tools or is poorly maintained, the vibration level
UniversalImpact
and noise emission value may differ. This may significantly
18
increase the vibration and noise emissions over the total
V= 18
working period.
To estimate vibration and noise emissions accurately, the
-1
min 0–400 times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
-1
min 0–1350
This may significantly reduce vibration and noise emissions
-1
min 0–20250
over the total working period.
Nm 30/18
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
mm 10
Assembly
mm 30
mm 8
u
mm 10
mm 6
kg 1.3–1.6
Charging the Battery
°C 0 to +35
u
°C –20 to +50
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
PBA 18V...W-.
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
AL 18...
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
Removing the battery
2
,
2
.
To remove the battery , press the battery release button and
pull the battery to the rear and out of the power tool. Do not
use force to do this.
Changing the tool (see figure A)
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Wear protective gloves when changing tools. There is
a risk of injury when touching the application tools.
1 609 92A 6DJ | (25.06.2021)
English | 13