Publicidad
Idiomas disponibles
Idiomas disponibles
ENG
ORIGINAL
material feed pump to a horizontal position also
allows removal of the pump from the coating material
►
container
Ensure that the locking pin locks.
OPERATING POSITION I.
►
Swiveling the material feed pump to a vertical
position allows the material feed pump to be
immersed in the coating material container (21).
OPERATING POSITION II.
►
Swivel material feed pump to a slanted (45°)
postion if using the container suction system (not
►
included) (22)
In this position, there is open
space under the material feed pump.
CHANGING THE MATERIAL FEED PUMP
POSITION.
►
Be careful, as the moving parts of the swivel
mechanism can crush fingers and feet
handle with one hand (23)
with the other hand (24)
pump up or down to the desired position, until the
locking pin locks into the new position.
TAKING THE UNIT INTO OPERATION WITH
COATING MATERIAL.
►
If the unit is located on a non-conductive surface
(e.g. a wood floor), earth the unit with an earthing
►
cable
Push locking pin and swivel material feed
pump into the coating material container (25)
►
Turn the pressure control knob on the hydraulic
pump to the left (pressure reduction) until it stops
►
(26)
Turn the relief valve handle (27) fully
counterclockwise (28)
INTERRUPTION OF WORK.
►
Close the hydraulic ball valve on the material
►
feed pump (29)
Flow of hydraulic oil to hydraulic
motor of material feed pump is interrupted
the relief valve handle fully counterclockwise (30)
Turn off the gasoline engine
►
of the spray gun in order to release the pressure
from the high-pressure hose and spray gun
►
Secure the spray gun (31)
tube immersed in the coating material or immerse
it in the corresponding cleaning agent
drying or two-component coating material is
used, ensure that the unit is rinsed with a suitable
cleaning agent within the processing time.
►
Grip
►
Push locking pin
►
Swivel material feed
►
Start the engine.
►
Pull the trigger
►
Leave the suction
►
If fast-
HYDRAULIC PUMP.
►
To start the hydraulic pump, turn the knob until
it is vertical (32)
will be disconnected (33).
PRIME/SPRAY
►
This switch toggles the unit between the
"priming" and "spraying" mode (34).
NOZZLE.
►
The nozzle is reversible and removable to
make cleaning and unclogging easier
"spray" position to use the airless gun (35)
to the opposed position to clean the nozzle (36).
PRESSURE CONTROL KNOB.
►
The pressure control regulator can be adjusted
to define different spraying intensities (37).
INSTALATION.
►
Remove or cover objects that you want to
protect from overspray (paint mist)
paint hose to paint hose outlet and tighten with
wrench (38)
and tighten with two wrenches (39)
pressure control regulator to the lowest setting
(40).
RELIEVE PRESSURE.
Turn power switch "off" (41)
►
spray" switch to "prime" mode to safely release
most pressure (42)
pail and activate the airless gun trigger to relieve
an remaining pressure (43)
"prime" mode between uses.
PRIME AIRLESS GUN.
This procedure is used for first time operation
►
and also to flush storage fluids out of the airless
►
Turn
For oil-based paint, flush with mineral
►
gun
spirits followed by warm clean water
to prevent fire: When using mineral spirits,
ground airless gun by holding it against a metal
container while flushing
paint, flush with warm clean water.
PRIME AND STARTUP.
►
Place priming tube in waste bucket (44)
Submerge suction tube in water or flushing
►
solvent (45)
English
9
►
In horizontal position the valve
►
Attach paint hose to airless gun
►
Turn "prime/
►
Point airless gun into paint
►
Note: Always set to
►
For water-based (latex)
►
Turn "prime/spray" switch to
►
Turn to
►
Turn
►
Attach
►
Turn the
►
Warning!
Publicidad
