Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION AND OPERATION MANUAL
18
5.1.6. TIMER OPERATION PROCEDURE
Setting current day and time
”
1. Hold down the SELECT (
mode. SET is indicated and the day blinks. All the days except the current day are indicated.
2. Hold down the SELECT (
The date is indicated, and the time blinks.
3. Press the SELECT (
again. "Hour" is indicated and "minutes" blinks.
4. Press the SELECT (
again. The current time setting mode ends and returns to normal mode. "Minutes" is indicated and the
SET indication goes out. The "seconds" start from zero.
Setting the timer (programming)
”
1. Press the TIMER switch. SET and SCHEDULE are indicated. Schedule number "1" blinks and other
numbers are indicated.
2. When the SCHEDULE switch (
[1] → [2] → [3] → [4] → [S] → [1]→....
Select [S] to set the ON/OFF time and temperature shifts.
−
By pressing the TIMER switch, the SET and SCHEDULE indicators go out and the mode changes back
−
to normal.
3. When the OK switch is pressed, the selected schedule number is indicated. The other schedule number
indicators go out, and the ON time "hour" indicator for the number selected blinks.
4. Press the SELECT (
again. "Hour" is indicated and "minutes" blinks.
5. Press the SELECT (
again. "Minutes" is indicated and the OFF time "hour" setting blinks.
6. Set the OFF time the same way as the ON time. After setting the "minutes", the OFF time is indicated. If
the schedule number [1][2][3][4] is selected, the indication changes to set the schedule number shown in
2. If [S] is selected, see the section on setting temperature shifts for details.
7. By pressing the (
the mode returns to normal.
Defining the schedule to be applied
”
1. Hold down the (
appears. All the days and schedule numbers are indicated.
2. Press the (
day blinks [Mon] → [Tue] →... → [Sun]→ [Mon~Sun] → [Mon~Fri] → [Sat, Sun] → [Mon]... If several
days are blinking, the same setting will be applied to all the days.
3. Press the (
) DAY switch until the schedule number you wish to set blinks.
4. Press the (
) SCHEDULE, and the SCHEDULE indication appears. Then the schedule number
indicated in step 3 is applied to the days set in step 2. Press the OK switch to activate or deactivate the
schedule. If the schedule is activated, the word SCHEDULE is lit up.
5. Press the TIMER switch and the mode returns to normal.
PMML0197_r0_04-10.indb 18
) DAY switch for more than 3 seconds to change to current day setting
) DAY switch until the current day blinks, then press OK.
) DAY / SCHEDULE switches to adjust the "hour" setting, and then press
) DAY / SCHEDULE switches to adjust the "minutes" setting, and then press
) is pressed, the schedule number moves
) DAY / SCHEDULE switches to adjust the "hour" setting, and then press
) DAY / SCHEDULE switches to adjust the "minutes" setting, and then press
) DAY / SCHEDULE switches, the SET and SCHEDULE indicators go out and
) DAY/SCHEDULE switches for more than 3 seconds and the SET indicator
) DAY/SCHEDULE switches until the day you wish to set blinks. When pressed, the
SET Mon Tue Wed Thu Fri
Sat
Sun
:
SET Mon Tue Wed Thu Fri
Sat
Sun
:
SET
Wed
:
Wed
:
1234S
SET
:
:
SCHEDULE
ON
4
OFF
SET
1234S
:
:
SCHEDULE
ON
4
OFF
ADDS
RNkHR
SET
1
:
SCHEDULE
:
ON
4
OFF
SET
1
:
:
SCHEDULE
ON
4
OFF
1
SET
:
:
SCHEDULE
ON
4
OFF
1
SET
:
:
SCHEDULE
ON
4
OFF
S
Mon
:
NEXT SCHEDULE
:
OFF
SET Mon Tue Wed Thu Fri
Sat
Sun
1234S
:
:
ON
4
OFF
Sun
SET Mon Tue Wed Thu Fri
Sat
1234S
:
:
ON
4
OFF
Sun
SET Mon Tue Wed Thu Fri
Sat
1234S
:
:
SCHEDULE
ON
4
OFF
Mon
:
NEXT SCHEDULE
:
OFF
08/07/2010 9:20:18
Publicidad
