Mitsubishi Electric CITY MULTI PKFY-P VKM-E Serie Manual De Instrucciones página 7

5. Operation
<To Stop Operation>
Press the ON/OFF button 1 again.
1 and the display area go dark.
Note:
Even if you press the ON OFF utton i
the operation is progress, the air conditioner
inutes. This is to prevent the internal co ponents fro
5.2. Operation ode select
Press the operation mode (
operation mode 2.
Cool mode
Dry mode
Fan mode
Heat mode
Automatic (cool/heat) operation mode
Auto atic operation
According to a set temperature, cooling operation starts if the room
temperature is too hot and heating operation starts if the room
temperature is too cold.
During automatic operation, if the room temperature changes and
remains 1.5 °C or more above the set temperature for 3 minutes, the
air conditioner switches to cool mode. In the same way, if the room
temperature remains 1.5 °C or more below the set temperature for
3 minutes, the air conditioner switches to heat mode.
Cool mode
3 minutes (switches
from cooling to heating)
Because the room temperature is automatically adjusted in order to
maintain a fixed effective temperature, cooling operation is performed
a few degrees warmer and heating operation is performed a few
degrees cooler than the set room temperature once the temperature is
reached (automatic energy-saving operation).
5.3. Te perature setting
To decrease the roo te perature:
Press button 3 to set the desired temperature.
The selected temperature is displayed 3.
To increase the roo te perature:
Press button 3 to set the desired temperature.
The selected temperature is displayed 3.
Cooling/Drying: 19 - 30 °C
Heating: 17 - 28 °C
Automatic: 19 - 28 °C
temperature is lower or higher than the displayed temperature.
ediately after shutting do n
ill not start for a out three
eing da aged.
) button 2 and select the
3 minutes (switches
from heating to cooling)
Set temperature +1.5°C
Set temperature
Set temperature -1.5°C
5.4. Fan speed setting
Press the Fan Speed button 5 as many times as necessary while the
system is running.
shown at 5.
FAN SPEED
Speed 1
2 speed
model
Speed 1
3 speed
model
Speed 1
4 speed
+
Auto *
* For MA remote controller only.
Automatic fan speed setting is necessary for wireless remote controller.
Note:
The nu er of availa le fan speeds depends on the type of unit
connected. Note also that so e units do not provide an "Auto" setting.
In the follo ing cases, the actual fan speed generated y the unit
fro the speed sho n the re ote controller display.
1. hile the display is sho ing "STAND BY" or "DEFROST".
2. hen the te perature of the heat e changer is lo
(e.g. i ediately after heat operation starts)
3. In HEAT ode, hen roo te perature is higher than the te perature
setting.
4. hen the unit is in DRY ode.
Automatic fan speed setting (For wireless remote controller)
It is necessary to set for wireless remote controller only when
automatic fan speed is not set at default setting.
It is not necessary to set for wired remote controller with automatic
fan speed at default setting.
1 Press the SET button with something sharp at the end.
Operate when display of remote controller is off.
blinks and Model No. is lighted A
MODEL SELECT
2 Press the AUTO STOP button.
blinks and setting No. is lighted B
(Setting No.01: without automatic fan speed)
3 Press the temp. buttons to set the setting No.02.
(Setting No.02:with automatic fan speed)
If you mistook the operation, press the ON/OFF
operate again from procedure 2.
4 Press the SET button with something sharp at the end.
and Model No. are lighted for 3 seconds, then turned off.
MODEL SELECT
MODEL SELECT
ON/OFF
FAN
MODE VANE
CHECK LOUVER
TEST RUN
14
SET RESET CLOCK
Display
Speed 2
Speed 2 Speed 3
Speed 2 Speed 3 Speed 4
in the heat
.
.
button and
B
A
TEMP
3
AUTO STOP
2
AUTO START
h
min
Auto
ill differ
ode.
7