EINHELL TC-SM 216 Manual De Instrucciones Original página 24

5.5 Precision adjustment of the angle stop
for crosscut 90° (Fig. 8, 9)
•
Lower the machine head (4) and fasten in
place with the retaining pin (30).
•
Fasten the turntable (19) in 0° position.
•
Undo the locking grip (26) and tilt the machi-
ne head (4) all the way to the right to 0° using
the handle (1).
•
Place the 90° angular stop (a) between the
blade (7) and the turntable (19).
•
Slacken the lock nut (37) and adjust the ad-
justment screw (35) until the angle between
the blade (7) and the turntable (19) equals
90°.
•
Retighten the lock nut (37) to secure this
setting.
•
Finally, check the position of the pointer (24).
If necessary, release the pointer with a cros-
stip screwdriver, move to the 0° position of the
angle scale (25) and retighten the pointer.
•
The angle stop (a) and crosstip screwdriver
are not included in the scope of this delivery.
5.6 Precision adjustment of the angle stop
for miter cut 45° (Fig. 8, 10)
•
Lower the machine head (4) and fasten in
place with the retaining pin (30).
•
Fasten the turntable (19) in 0° position.
•
Undo the locking grip (26) and tilt the machi-
ne head (4) all the way to the left to 45° using
the handle (1).
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (19).
•
Slacken the lock nut (37) and adjust the ad-
justment screw (36) until the angle between
the blade (7) and the turntable (19) equals
exactly 45°.
•
Retighten the lock nut to secure this setting.
•
No angle stop (b) included.
6. Operation
Warning! To make 90° crosscuts, the adjustable
stop rail (14) must be fi xed at the inner position:
•
Undo the locking grip (15) for the adjustable
stop rail and push the adjustable stop rail
inwards.
•
The adjustable stop rail (14) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (14) and
the saw blade (7) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
Anl_TC_SM_216_SPK13.indb 24
GB
and the saw blade cannot collide.
•
Tighten the locking grip (15) again.
Warning! To make 0°-45° miter cuts (with the ma-
chine head (4) inclined or the turntable set at an
angle), the adjustable stop rail (14) must be fi xed
at an outer position.
•
Undo the locking grip (15) for the adjustable
stop rail and push the adjustable stop rail
outwards.
•
The adjustable stop rail (14) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (14) and
the saw blade (7) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking grip (15) again.
6.1 Cross cut 90° and turntable 0°
(Fig. 1-3, 11)
For cutting widths up to approx. 100 mm it is
possible to fi x the saw's drag function with the
locking screw for drag guide (29) in rear position.
If the cutting width exceeds 100 mm you must
ensure that the locking screw for drag guide (29)
is slackened and that the machine head (4) can
be moved.
•
Move the machine head (4) to its upper po-
sition.
•
Use the handle (1) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
•
Place the piece of wood to be cut at the stop
rail (13) and on the turntable (19).
•
Lock the material with the clamping device
(8) on the fixed saw table (18) to prevent the
material from moving during the cutting ope-
ration.
•
Press the release button (3) to release the
On/Off switch (2).
•
Press the On/Off switch (2) to start the motor.
•
With the drag guide fixed in place: Use the
handle (1) to move the machine head (4)
steadily and with light pressure downwards
until the saw blade (7) has completely cut
through the workpiece.
•
With the drag guide not fixed in place: Pull
the machine head (4) all the way to the front
and then use the handle (1) to move it down-
wards steadily and with light pressure. Now
push the machine head (4) slowly and steadi-
ly to the very back until the saw blade (7) has
completely cut through the workpiece.
- 24 -
05.12.2022 09:37:35