EINHELL TC-SM 216 Manual De Instrucciones Original página 25

•
When the cutting operation is completed,
move the machine head (4) back to its upper
(home) position and release the On/Off but-
ton (2).
Important! The integral resetting springs will au-
tomatically lift the machine head. Do not simply
let go of the handle (1) after cutting, but allow the
machine head (4) to rise slowly, applying slight
counter pressure as it does so.
6.2 Cross cut 90° and turntable 0° - 45°
(Fig. 1-3, 12)
The crosscut saw can be used to make crosscuts
of 0°- 45° to the left and 0° - 45° to the right in re-
lation to the stop rail.
•
Swing up the machine head (4).
•
Move the locking lever (20) to its top position
to enable the turntable to be adjusted.
•
While holding the release button (21) pressed
down, turn the turntable (19) and scale poin-
ter (22) to the desired angular setting on the
scale (23).
•
To lock the turntable (19), press the locking
lever (20) down.
•
Cut as described in section 6.1.
6.3 Miter cut 0°- 45° and turntable 0°
(Fig. 1-3, 13)
The crosscut saw can be used to make miter cuts
of 0- 45° in relation to the work face.
•
Move the machine head (4) to its upper po-
sition.
•
Fasten the turntable (19) in 0° position.
•
Release the locking grip (26) and tilt the
machine head (4) to the left until it coincides
with the required angular setting on the scale
pointer (24) on the scale (25). Then secure
the locking grip (26) again.
•
Cut as described in section 6.1.
6.4 Miter cut 0°- 45° and turntable 0°- 45°
(Fig. 1-3, 14)
The crosscut saw can be used to make miter cuts
to the left of 0°-45° in relation to the work surface,
with simultaneous setting of the turntable from
0°-45° to the left or 0°-45° to the right in relation to
the stop rail (double miter cut).
•
Move the machine head (4) to its upper po-
sition.
•
Move the locking lever (20) to its top position
to enable the turntable to be adjusted.
•
While holding the release button (21) pressed
down, turn the turntable (19) and scale poin-
ter (22) to the desired angular setting on the
scale (23).
Anl_TC_SM_216_SPK13.indb 25
GB
•
To lock the turntable (19), press the locking
lever (20) down.
•
Release the locking grip (26) and tilt the
machine head (4) to the left until it coincides
with the required angular setting on the scale
pointer (24) on the scale (25). Then secure
the locking grip (26) again.
•
Cut as described in section 6.1.
6.5 Limiting the cutting depth (Fig. 15)
•
The cutting depth limiter can be activated with
the help of the screw (34).
•
To do so, slacken the screw (34) using a cros-
stip screwdriver, so that the stop plate can be
moved. Then move the stop plate (33) as far
as possible towards the saw blade and retigh-
ten the screw (34) afterwards.
•
The cutting depth can be infinitely adjusted
using the knurled screw (31). To do so, sla-
cken the lock nut (32) and set the required
cutting depth by turning the knurled screw
(31) in or out. Then retighten the lock nut (32)
on the screw (31).
•
Check the setting by completing a test cut.
•
A crosstip screwdriver is not supplied with
the product.
6.6 Sawdust bag (Fig. 2)
The saw is equipped with a sawdust bag (27) for
sawdust and chips.
The sawdust bag (27) can be emptied by means
of a zipper at the bottom.
6.7 Replacing the saw blade (Fig. 1, 16)
•
Before changing the saw blade: Pull out the
power plug!
•
Wear work gloves to prevent injury when
changing the saw blade.
•
Swing the machine head upwards (4).
•
Press the saw shaft lock (5) with one hand
while positioning the hexagon key (45) on the
flange bolt (38) with the other hand. The saw
shaft lock (5) engages after no more than one
rotation.
•
Now, using a little more force, slacken the
flange screw (38) in the clockwise direction.
•
Turn the flange screw (38) right out and remo-
ve the washer (40) and the outer flange (39).
•
Take the blade (7) off the inner flange and
pull out downwards. To do so, move the saw
blade guard (6) up to enable access to the
saw blade.
•
Carefully clean the flange screw (38), washer
(40), outer flange (39) and inner flange.
- 25 -
05.12.2022 09:37:36