Publicidad
Idiomas disponibles
Idiomas disponibles
PRODUCT SPECIFICATIONS
ENGINE
Engine Type ............................. 80cc Overhead Valve (OHV)
Spark Plug .............................. NGK BPR7HS or equivalent
Lubricant Fill Volume ..................................... approx. 12 oz
Fuel Volume................................................................. 1.2 gal.
*Rated output determined by PGMA Standard G300
KNOW YOUR GENERATOR
See Figure 1.
The safe use of this product requires an understanding of the
information on the product and in this operator's manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
120 V AC RECEPTACLES
Your generator has two single phase, 60 Hz outlets that are
120 Volt AC, 20 Amp receptacles. These can be used for
operating appropriate appliances, electrical lighting, tools,
and motor loads.
AIR FILTER
The air filter help to limit the amount of dirt and dust drawn
into the unit during operation.
AUTO IDLE BUTTON
The auto idle button is used to control the speed of the
engine and conserve fuel. When Auto Idle is on and no
appliances are connected to the unit, the engine will idle.
If an appliance is added, the engine speed will increase to
power the item. If the appliance is removed, the engine will
return to idle.
AUTOMATIC SHUTOFF
The generator's carbon monoxide sensor is designed to
monitor the level of carbon monoxide present during genera-
tor operation. If the unit is positioned incorrectly and carbon
monoxide levels rise to an unsafe level, the LED on the sensor
will flash red and the generator will automatically shut down.
Leave the area immediately and relocate to an open outdoor
area. Ventilate the area thoroughly before occupying again.
Ensure the generator is located in an open, outdoor area at
least 20 feet away from all doors, windows, and occupied
spaces, and point exhaust away from occupied structures
before restarting.
NOTE: After a shutoff event has occured, the LED will con-
tinue to flash red for up to 20 minutes. Once the generator
is relocated and CO levels are safe, the generator can be
restarted even if the light is still flashing.
CARRY HANDLES
The generator is equipped with three carry handles for
easy transport. The handles should be used to carry the
generator.
FEATURES
GENERATOR
Rated Voltage .............................................120V AC/5V DC
Rated Amps ...............................................15A AC/2.1A DC
Rated Output*......................................................... 1,800 W
Starting Watts ......................................................... 2,300 W
Rated Frequency ........................................................ 60 Hz
EASY START DIAL
The Easy Start dial is used when starting, stopping, and run-
ning the engine. It also controls the choke and the fuel valve.
FUEL TANK
The fuel tank has a capacity of 1.2 gallons.
GENCONTROL™ WITH BLUETOOTH
The GENControl™ monitoring system with Bluetooth
tracks fuel level, runtime, auto idle status and load.
GROUND TERMINAL
The ground terminal is used to assist in properly grounding
the generator to help protect against electrical shock. Con-
sult with a qualified local electrician for grounding require-
ments in your area.
LOW OIL SHUT DOWN PROTECTOR
The low oil sensor causes the engine to stop if the level of
lubricant in the crankcase is insufficient.
OIL CAP/DIPSTICK
Remove the oil fill cap to check and add lubricant to the
generator when necessary.
PARALLEL KIT TERMINALS
The non-polarized parallel kit terminals are used with a
parallel kit (sold separately) that will allow generators to be
linked together to increase output.
NOTICE:
Do not disconnect cables while the generator is running.
The generator or the load may be damaged.
NOTE: Read and understand the parallel kit's instructions
prior to use.
RECOIL STARTER
The recoil starter is used (along with the Easy Start dial) to
start the generator's engine.
RESET BUTTON
The reset button is used to restore power if an overload
occurs. To restore power, remove the last electrical load
added, then press the reset button.
10 — English
®
®
Publicidad
