Before Use; Operation - Hitachi Koki DS 14DFL Manual De Instrucciones

Taladro atornillador a bateria
Ocultar thumbs Ver también para DS 14DFL:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

5.
Remove the battery from the battery charger.
Supporting the battery charger with hand, pull out
the battery from the battery charger.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries
and batteries that have not been used for an
extended period is not activated, the electric
discharge might be low when using them the first
and second time. This is a temporary
phenomenon, and normal time required for
recharging will be restored by recharging the
batteries 2 – 3 times.
CAUTION:
● When the battery charger has been continuously
used, the battery charger will be heated, thus
constituting the cause of the failures. Once the
charging has been completed, give 15 minutes rest
until the next charging.
● If the battery is charged while it is heated because
it has been left for a long time in a location subject
to direct sunlight or because the battery has just
been used, the pilot lamp of the charger lights for
1 second, does not light for 0.5 seconds (off for
0.5 seconds).
The battery will not be recharged. In such a case,
let the battery cool before charging.
NOTE:
Charging times may be longer depending on the
surrounding temperature and battery conditions.
Charge time lamp indications are only a guide, and
may vary depending on the surrounding
temperature and battery conditions.
Remove the battery from the charger when not in
use.
How to make the batteries perform longer.
Recharge the batteries before they become
completely exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust
the electric current, the battery may be damaged
and its life will become shorter.
Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately
after use. If such a battery is recharged immediately
after use, its internal chemical substance will
deteriorate, and the battery life will be shortened.
Leave the battery and recharge it after it has cooled
for a while.

BEFORE USE

Check the work area to make sure that it is clear of debris
and clutter.
Clear the area of unnecessary personnel. Ensure that
lighting and ventilation is adequate.

OPERATION

1.
Using the hook (Hook with bit holder)
WARNING:
When using the hook, pay sufficient attention so
that the main equipment does not fall. If the tool
falls, there is a risk of accident.
CAUTION:
Do not attach the tip tool except phillips bit to the
tool main unit when carrying the tool main unit
with the hook suspended from a waist belt.
Injury may result if you carry the equipment
suspended from the waist belt with sharp tipped
components such as drill bit attached.
The hook can be installed on the right or left side
and the angle can be adjusted in 5 steps between
0° and 80°.
(1) Operating the hook
(a) Pull out the hook toward you in the direction
of arrow (A) and turn in the direction of arrow
(B) (Fig. 7).
3
2
(B)
1
(b) The angle can be adjusted in 5 steps (0°, 20°,
40°, 60°, 80°).
Adjust the angle of the hook to the desired
position for use.
(2) Switching the hook position
CAUTION:
If the tool falls, there is a risk that malfunction
and/or physical damage can occur. It is
recommended that you also use fall-preventing
wires, etc.
Incomplete installation of the hook may result in
bodily injury when used.
(a) Securely hold the main unit and remove the
screw using a slotted head screwdriver or a
coin (Fig. 8).
English
5
4
(A)
Hook
Fig. 7
15

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ds 18dfl

Tabla de contenido