Christie CP4445-RGB Manual De Instrucciones página 5

Light intensity hazard distance
This projector has been classified as Risk Group 3 as per the IEC
62471-5:2015 standard due to possible hazardous optical and
thermal radiation being emitted.
Warning! If not avoided, the following could result in
serious injury.
• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct
exposure to the beam must be permitted. Class 1 Laser
Product - Risk Group 3 according to IEC 60825-1:2014
and IEC 62471-5:2015.
•
PERMANENT/TEMPORARY BLINDNESS HAZARD!
Operators must control access to the beam within the
hazard distance or install the product at the height that
prevents exposure of spectators' eyes within the hazard
distance. The hazard zone must be no lower than 2.5
meters (US installations) or 2.0 meters (global
installations) above any surface upon which any persons
are permitted to stand and the horizontal clearance to
the hazard zone must be a minimum 1.0 meters.
• EXTREME BRIGHTNESS! Do not place reflective objects in
the product light path.
The following diagram shows the zones for ocular and skin
hazard distances:
• A—Hazard zone. The region of space where the
projection light from the laser-illuminated projector is
above emission limits for Risk Group 2. The light
intensity may cause eye damage after a momentary or
brief exposure (before a person can avert his or her eyes
away from the light source). The light may cause skin
burns to occur.
• B—Hazard distance. Operators must control access to the
beam within the hazard distance or install the product
preventing potential exposure of the spectators' eyes
from being in the hazard distance.
• C—No access zone. Horizontal clearance of the no access
zone must be a minimum of 1.0 meters.
• D—Vertical distance to hazard zone. The hazard zone
must be no lower than 2.5 meters (US installations) or
2.0 meters (global installations) above any surface upon
which any persons are permitted to stand.
CP4445-RGB and CP4455-RGB Product Safety Guide
020-103745-01 Rev. 1 (12-2022)
Copyright © 2022 Christie Digital Systems USA, Inc. All rights reserved.
If printed, please recycle this document after use.
If the vertical distance to hazard zone requirement (Zone
D) is satisfied, the horizontal clearance distance (Zone C)
is not needed.
• E—Represents the top view of the projector.
• F—Represents the side view of the projector.
For information detailing the hazard distance for each lens, refer
to the CP4445-RGB and CP4455-RGB Installation and Setup
Guide (P/N: 020-103746-XX).
For Installations in the United States
The following must be in place for laser-illuminated projector
installations in the United States:
• The projection room shall be clearly identified by the
posting of laser warning and restricted access signs, and
by restricting entry through physical means. The
projection room sign must display the warning "No direct
exposure to beam shall be permitted".
• The Christie Laser Projection System Installation
Checklist must be fully completed after the installation
and sent to lasercompliance@christiedigital.com. A copy
can remain on-site. This checklist can be found as a
separate document in the accessory box with the
manual.
• Certain US states have additional laser regulatory
requirements. Contact
lasercompliance@christiedigital.com for additional
regulatory requirements.
Power specifications
CP4445-RGB
Item Main input
A
Voltage range 200-240 VAC,
single phase
Maximum 10 A
current
Line frequency 50/60 Hz
CP4455-RGB
Item Main input
A
Voltage range 200-240 VAC,
single phase
Maximum 13 A
current
Line frequency 50/60 Hz
Technical support
Technical support for Christie Cinema products is available at:
• Support.cinema@christiedigital.com
Important Safety Information
Main input UPS input
B
200-240 VAC, 100-240 VAC,
single phase single phase
8 A 5 A
50/60 Hz 50/60 Hz
Main input UPS input
B
200-240 VAC, 100-240 VAC,
single phase single phase
8 A 5 A
50/60 Hz 50/60 Hz
5