Peg-Perego tatamia follow me Instrucciones De Uso página 14

child is kept away when unfolding and
folding this product.
A single product which follows the growth of your
child.
_ From 0 to 6 months, a comfortable recliner and swing.
_ From the age of 6 months, a high chair for eating,
playing and relaxing.
_ From the age of 12 months, a high chair without a
tray, for sitting at the table with the adults.
The images referring to the textile details may
differ from the collection purchased.
For more information, consult our website:
www.pegperego.com
INSTRUCTIONS FOR USE
1 ASSEMBLING THE WHEELS: Carefully assemble the
wheels correctly before opening the high chair.
ASSEMBLING THE REAR WHEELS:
the two rear wheels, with a red collar (fig. a), must be
hooked onto the rear base of the product, using the
high chair backrest as a reference (fig. b).
Insert the wheels and push the red collar as far as it
will go against the base (fig. c).
2 ASSEMBLING THE FRONT WHEELS:
the two front wheels, without a red collar (fig. d),
must be hooked onto the front base of the product,
using the footrest as a reference (fig. e). Insert them as
far as they will go against the base (fig. f).
3 OPENING: Lower the two support base sections one
after the other to open the high chair. Slightly tilt the
high chair to the side opposite the base section you
are lowering (fig_a) and check the green rectangle to
ensure it is open properly (fig_b).
WARNING: If the red rectangle is visible, the base
has not been opened properly.
4 Before using the high chair, raise the seat (fig_a),
completely recline the backrest until it clicks into
position (b) and make sure the pin is properly locked
in place (fig_c).
5 FIVE POINT SAFETY HARNESS: To fasten the harness,
insert the two waist strap buckles (with shoulder
straps attached) into the leg divider strap until you
hear a click (fig. a). To release it, press the sides of
the buckle and simultaneously pull the waist strap
outwards (fig. b). To tighten the waist strap, pull
from both sides in the direction of the arrow (fig. c).
To loosen it, do the opposite. The waist strap can be
tightened as far as the safety stop (fig. d).
6 The shoulder straps of the harness can be set at two
different heights. Partially remove the sack (fig_a),
release the shoulder straps from the backrest (fig_b)
and pull them out from the sack (fig_c).
7 Insert the ends of the shoulder straps in the other
slots in the sack (fig_d) and the backrest (fig_e),
then put the sack back into the right position on the
backrest.
8 BRAKE: The product is packaged with the brakes on.
To move the high chair, press the lever and move it
forward until you can see GO (fig. a).
This will allow the high chair to be moved around
freely; you don't need to keeping pressing it.
To put the brakes on, move the lever back until you
can see the word STOP and then release the button
(fig. b). Wheels are non-scratching.
RECLINER-SWING
9 FOOTREST FOR EARLY MONTHS: The high chair is
fitted with a footrest for use when it is in the recliner-
swing mode. Raise the footrest by rotating it upwards
(fig. a). Fold it away by pressing the two side buttons
(fig. b) and rotating it downwards (fig. c).
10 RECLINER-SWING: Before placing the high chair in
the recliner-swing mode, remove the tray (fig. a) and
insert the front bar (fig. b). To remove the protective
front bar, press the two buttons at its base and pull it
out (fig_c).
11 SWING: To transform the chair into a swing, place the
seat in the lowest position (fig. a) and press the red
buttons on the inner part of the uprights, pushing
them upwards (fig. b). Swing mode (fig. c).
12 To put it back in recliner or high chair mode, make
sure that the side uprights of the seat are parallel with
those of the frame (fig_a), then press the red buttons
and push them downwards (fig_b).
13 RECLINER CONFIGURATION: - Remove the tray. -
recline the backrest to the 3/4 position (fig_a) - lift the
footrest (fig_b) - the recliner's height can be adjusted
as needed (fig_c).
HIGH CHAIR
14 FOOTREST: Lower the footrest (fig. a), press the two
side buttons (fig. b) and select one of the three
available heights.
15 TRAY: To fit the tray, pull the central lever underneath
it towards you while at the same time pushing it all
the way into the armrests (fig_a). To extend or remove
the tray, pull the central lever underneath it towards
you (fig_b) and move it outwards (fig_c). To remove
the tray, pull the side levers outwards and pull the
tray towards you. The high chair has a double tray.
The top tray can be easily washed in a dishwasher. To
remove it, detach it from the lower tray and lift it up
(fig. d).
16 USE WITHOUT THE TRAY: to use the seat at the table,
remove the tray.
17 ADJUSTING THE HEIGHT: The seat can be set at 9
different heights. To raise or lower the seat, pull the
two levers upwards (fig. a) and move it to the required
position. This can also be done with the child in the
high chair.
18 RECLINING BACKREST: The seat can be reclined in four
positions: for eating, playing, relaxing or sleeping. To
adjust it, raise the handle behind the backrest (fig. a)
and lock it in the required position (fig. b). This can
also be done with the child in the high chair.
19 CLOSING AND REOPENING THE TRAY: Pull the central
lever underneath it towards you (fig_a) and extend
it as far as the red markers (fig_b), then swing it
upwards to lock it in place (fig_c). To reopen the
tray, swing it downwards then pull the central lever
towards you and put the tray in one of the positions
for use.
COMPACT CLOSURE: before closing the high chair,
20
it is necessary to fold up the tray. Put the backrest
in the vertical position, then pull the two red
levers on the sides of the seat outwards (Arrow_a).
Rotate it downwards (Arrow_b), lower the seat to
the bottom position and fold away the footrest. To
raise the support bases, press the red levers on the
sides of the uprights (Arrow_c) and at the same
time lift the grey levers (Arrow_d). The bases will
lift up automatically (Arrow_e). The high chair is
freestanding when folded up.
21 REMOVABLE COVERS: To remove the seat covers,
remove the upper part of the sack, then pull the
harness straps out through the backrest (fig. a) and
through the sack (fig. b). Push a screwdriver into the
hole in the leg divider and pull out the belt (fig. c).
22 Unbutton the sack at the sides (fig. d) and pull up to
remove it (fig. e).
SERIAL NUMBERS
23 Information about the production date of tatamia
follow me can be found under the base.
_ Product name, date of manufacture and serial
number.
- 14 -