Publicidad
Idiomas disponibles
Idiomas disponibles
Operating Instructions
hot during use, To avoid the risk of
severe burns, never touch the
discharge tube.
Check valve
- One*way valve that
allows air to enter the tank, but
prevents air in the tank from fJowing
back into the compressor pump,
Belt Guard
- Covers the belt. motor
pulley and flywheel,
Tank Drain
Valve
* This valve is
located
on the bottom
of the tank. Use
this valve to drain moisture from the
tank daily to reduce the risk of
corrosion.
Reduce tank pressure below 10 psi,
then drain moisture
from tank daily to
avoid tank corrosion. Drain moisture
from tank(s)
by opening
the drain
valve io_ated
underneath
the tank.
I_WARNING]
OlsCormect tag jnd lock
i;,_j_Jm
i
out power sou_,
th_
rel, ase all llressure
f_m
the system before
attempting
to Install, servlte,
rein(ate
or perform
any malntonance,
LOCATION
1"/1/scompressor/s
I
not Intended
for
ouldoor
installation.
it isextremely important
to install _e
compre_or
in a dean, weft ventilated
area where the surrounding air
temperature
will not be more than 100*F.
Provide a minimum
clearance
of 18
inches between
the compressor
flywheel
or fan to the wall and ensure
clear access to the drain cock to
facilitate
condensate
drainage.
Do not locate the compressor air inlet
near steam, paint spray, sandblast areas
or any other source of contamination.
MOUNTING
Nevlr use _
sk/_
for nmu*ffir, g the €om_e_.
FLOOR MOUNTING
(All Units)
On some 30 gallon models a wall cable
is provided
and should be installed.
If
the unit is not secured with the wall
cable, the compressor feet MUST be
bolted
to a fiat. even, concrete floor or
separate
concrete foundation.
Vibration
isolators must
be used
between
the tank leg and the floor
(Part number
MP3445 available
separately),
Do not draw bolts tight,
Allow the pads to absorb vibrations.
A
flexible
coupling should
be instaged
between
the tank and service piping.
JAWARNINGI
Thl,¢o._=..orl,
exl_emely
top
heavy. The unlf must be bolted to the
floor with Isolation
pads or se_-ured
with the wail cable (lt provlded)
before operating
to prevent
equipment
damage,
injury or death.
WALL CABLE INSTALLATION
(Provided
on some 30 gallon
models)
Included
with the safety cable are two
lag screws and washers.
1, Place an isolation pad beneath
each
foot of the compressor to minimize
vibration,
2. Position the cable through
the
baseplate
as shown in Figure 3.
3. Place the screws through
the
washers then through
looped
ends
of cable.
4. Secure the screws to a stud within a
framed
wall. Use anchors if the wall
is concrete.
DO not seoa_
the
compressor
w/th
toggle botts Into drywall.
Drywall
slleeff_
or pla_ter
will not suppo_
the weight of the compressor.
Never Install •
shut.off
valve
between
the €ompressor pump and the
tank. _rs_l
Injury andlor
equipment
damage ma I o¢oJr.
Vertical
Models
PIPING
Never use plastic
_
(Pvc) plpe for
compreSSed
air. Serious Injury or death
could re suit.
Any tube, pipe, or hose used must have
a pressure rating
higher then
150 psi.
Minimum
recommended
pipe size:
- up to 50 feet long use t/2"
- greater than 5Oft, long use 3/4"
Larger diameter
pipe is always better.
All wlHng and
L&WARNINGJ .l_¢.l
(onnecl_rons rnust be perfonned
by e
qualified
electrldan.
Insfallallons
must
be In ao:ordance
with local end
national
codes.
GROUNDING
This product must be grounded.
If the
unit comes with a factor/installed
cord, plug the cord into a properly
sized, grounded
outlet.
For unit5 that
do not have a factory installed cord,
install permanent
wiring
from the
electrical
source to the pressure switch
with a ground conductor
connected
to
the grounding
screw on the pressure
switch.
A properly sized cord with a
ground conductor
and plug may also
be installed
by the user.
Impn_x, rly grounded
motors
are shodc hazards.
Make sure ell the
equipment
Is properly
grounded.
WIRING
Local electrical wiring
codes differ from
area to area. Source wiring, plug and
protector
must he rated for at least the
amperage
and voltage indicated on the
motor nameplate,
and meet all electrical
codes for this minimum,
Use a slow blow
fuse _
T or a circuit breaker.
Overheetin_
shore
€lrcultlnll
and fire
d,uemge will result
from Im:d_tUet_
wiring,
Motor
protection
should be used when
a motor
built-in thermal
overload
protection
is not provided,
Some 3
phase unit_ require a magnetic
starter
3
Publicidad
