Husqvarna K1 PACE Manual Del Usuario página 10

to snag the rotating accessory and cause loss of
control or kickback.
• Do not attach a saw chain, woodcarving blade,
segmented diamond wheel with a peripheral gap
greater than 10 mm or toothed saw blade. Such
blades create frequent kickback and loss of control.
• Do not "jam" the wheel or apply excessive pressure.
Do not attempt to make an excessive depth of cut.
Overstressing the wheel increases the loading and
susceptibility to twisting or binding of the wheel in
the cut and the possibility of kickback or wheel
breakage.
• When wheel is binding or when interrupting a cut
for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes to
a complete stop. Never attempt to remove the wheel
from the cut while the wheel is in motion otherwise
kickback may occur. Investigate and take corrective
action to eliminate the cause of wheel binding.
• Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter
the cut. The wheel may bind, walk up or kickback if
the power tool is restarted in the workpiece.
• Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own
weight. Supports must be placed under the
workpiece near the line of cut and near the edge of
the workpiece on both sides of the wheel.
• Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding
wheel may cut gas or water pipes, electrical wiring or
objects that can cause kickback.
General safety instructions
WARNING:
instructions that follow before you use the
product.
• A power cutter is a dangerous tool if used carelessly
or incorrectly and can cause serious injury or death.
It is very important that you read and understand
the contents of this operator's manual. It is also
recommended that first time operators also obtain
practical instruction before using the product.
• Do not do modifications to this product. Modifications
that are not approved by the manufacturer, can
cause serious injury or death.
• Do not operate the product if it is possible that other
persons have done modifications to the product.
• Always use original accessories and spare parts.
Accessories and spare parts that are not approved
by the manufacturer, can cause serious injury or
death.
• Keep the product clean. Make sure that you can
clearly read signs and decals.
• Never allow children or other persons not trained in
the use of the product to use or service it.
10
Read the warning
• Do not let a person operate the product unless they
read and understand the contents of the operator's
manual.
• Only let approved persons operate the product.
• The safety distance for the power cutter is 15 m/50
ft. Make sure that animals and bystanders are not in
the work area.
• This product produces an electromagnetic field
during operation. This field can under some
circumstances interfere with active or passive
medical implants. To decrease the risk of serious
injury or death, we recommend persons with medical
implants to speak to their physician and the medical
implant manufacturer before operating this product.
• The information in this operator's manual is never
a substitute for professional skills and experience.
If you are in a situation where you feel unsafe,
stop and get expert advice. Speak to your servicing
dealer. Do not try any task that you feel unsure of.
Battery safety
WARNING:
instructions that follow before you use the
product.
WARNING:
cause an explosion and cause injury. If the
battery has a deformation or is damaged,
speak to an approved HUSQVARNA service
agent.
• Only use the Husqvarna PACE batteries that we
recommend for your product. The batteries are
software encrypted.
• Use only original batteries for this product. There is
a risk of explosion if the batteries are replaced with
a battery of incorrect type. Speak to your dealer for
more information.
• Use Husqvarna PACE batteries that are rechargable
as a power supply for the related HUSQVARNA
products only. To prevent injury, do not use the
battery as a power supply for other devices.
• Risk of electrical shock. Do not connect the battery
terminals to keys, screws or other metal. This can
cause a short circuit of the battery.
• If the battery leaks, do not let the liquid touch your
body, clothes or the product. If you touch the liquid,
clean the area with a large quantity of water and get
medical aid.
• Use protective glasses when you are near batteries.
If you get liquid in your eyes, do not rub but flush
with water for a minimum of 15 minutes. Get medical
aid.
• Do not use batteries that are non-rechargable.
• Do not do modifications to the battery.
• Do not put objects into the air slots of the battery.
Read the warning
A damaged battery can
1598 - 007 - 28.09.2023