Publicidad
Idiomas disponibles
Idiomas disponibles
®
®
completely
stopped
before
touching
them.
Before your first cut, adjust
the mower
cutting
height
to the
desired
position.,
The
mower
can be set to one of six cutting
heights,
with
cutting
heights
between
3/4"
and
2-3/4':
To
adjust
the cutting
height,
press the top of cut
lever
(6) outwards,
at the same
time
lift or
push
down
the mower
until
required
height
is selected..
11o
It_OWIING
For' cutting
convenience,
it may be best to start
mowing
at a point
close to the power
supply
and to work
your
way away from the supply.
Mow the lawn at a right
angle from the power'
supply and place the power cable to side which
has already
been cut.
_
Warning:When
mowing
do not allow
the
motor
to
labor,
particularly
in
heaw
conditions.
When
the
motor
labors,
the
speed
of
the
motor
cJrops
and
you
will
hear
a change
in the
motor
sound.
VJt_e, this occurs,
stop mowiug.
Release
the
switch
lever
and
raise
the
height
of
cut.
Failure
to
do so could
damage
the
machine.
Position
6
5
4
Height of cutting
3/4"
1-1/8"
1-9/16"
3
2"
2
2-3/8"
1
2-3/4"
MAINTENANCE
_
Warni,
g: Stop
mower
aud
remove
plug from
the power
supply
before
removing
the grass
box.
Note:To
ensure
long and reliable
service,
carry
out
the
following
maintenance
procedures
regularly,
Check for obvious
defects
such as
a loose,
dislodged
or damaged
blade,
loose
fittings,
and worn
or damaged
components,
Check
that
the
covers
and
guards
are
all
undamaged
and
are
correctly
attached
to
mower.
Carry out any necessary
maintenance
or
repairs
before
operating
mower°
If the
mower
should
happen
to fail despite
regular
maintenance,
please call our customer
helpline
for advice_
BLADE
MJZ_gNTENANC=
[See L]
Never
cam/out
any assembly
operations
or adjustments
w_th the power
connected
to
the
mower.
Airways
ensure
that
the
power
button
is in the
off
position
and
that the power
plug is disconnected
from
the
supply.
JUways
handle
the
bgade with
care-sharp
edges
could
cause
injury.
Use
gloves.
Follow these procedures
to remove
and replace
the blade. You will need protective
gloves
(not
provided)
and a spanner wrench
(not provided)
to remove
the blade,
Hold the blade
(13) and
unscrew
the blade bolt (7)anti clockwise
using
a spanner
wrench.
Remove
blade
and attach
a new one to the blade
bolt_
Ensure that the
blade
is properly
positioned
as seen in Fig. K,
then
firmly
tighten
the bolt.
DO &lOT
OVER
TIGHTEN.
Renew your metal blade after" 50hrs mowing
or
2 years ,which ever is the sooner-regardless
of
condition.
gf the blade is cracked
or damaged
replace
it with
a new one.
STORAGE:
Rotate
_dl=e Upper
Handle
knob
to
release
the upper handle.
Always
ensure
that
the
power
button
is in
the
off position
and
that
the
power
plug
is
disconnnected
from the supply.
Clean the exterior
of the machine
thoroughly
using a soft brush and cloth. Do not use water,
solvents
or polishes.
Remove
all grass
and
debris,
especially
from the ventilation
slots.
Turn the machine
on its side and clean the blade
area°
If grass
cuttings
are compacted
in the
blade
area, remove
with
a wooden
or plastic
implement°
Store the machine
in a dry place, Do not place
other' objects on lop of the machine.
Rotate
the Upper
Handle
knob
(4) to release
the handle joint,
it can be folded.You
can carry
the mover
by middle
carry handle(l!}
and front
carry handle{12).(See
M.1,M.2)
To aid storage,
loosen
the lower
handle
knobs
(16} and fold the handles..
Ensure cables are not stuck or entangled
when
®
I
NA-WG712-M-070115,indd
10
2007-1-15
I6:53:01
Publicidad
