Holex HCT Manual Del Usuario página 14

HOLEX HCT electronic torque wrench
de
1. If a password is required, press the Left/Back key in the main menu.
2. Select "Settings" and confirm with OK.
3. Use up and down to select the desired menu item, and confirm with OK.
11.1. DISPLAY
en
SETTINGS
Display
Measurement
System
bg
Menu
1. Select "Display" and confirm with OK.
2. Configure the following settings:
zh
Brightness Set screen brightness in percent.
Standby Set inactive time until torque wrench switches off.
Dimming Set inactive time until display switches off.
da
Time Format Set the time in the format 12 h/24 h.
Date Set the date in the format DD.MM.YYYY.
Time Set time.
fi
11.2. MEASUREMENT
back
Measurement mode
SETTINGS
fr
Display
Measurement
System
it Menu
hr
lt
Effective length
nl
1. Select "Measurement" and confirm with OK.
2. Configure the following settings:
no Unit
pl Threshold
Evaluation time
pt
Effective length
Alarm
ro
Vibration
Counter
sv
Counter Reset
11.3. SYSTEM
sk
back
Measurement mode
SETTINGS
Display
sl Measurement
System
Menu
es
1. Select "System" and confirm with OK.
2. Configure the following settings:
Language
Factory setting
cs
Master PWD
hu
14
back
Measurement mode
DISPLAY BRIGHTNESS
Brightness 90 %
Standby 10 min 90 %
Dimming 5 sec
Settings 1/6
Display
MEASUREMENT
Unit
Nm
Threshold 75%
Evaluation time 5 sec
1/8
Settings
Set the unit of measurement for torque
measurement in the "Display" mode. This
unit will act as the default unit when a
screw case is created.
Value in percent above the lower target
value that when reached triggers the
buzzer and vibration to alert the user.
Time after the tightening procedure until
the value of the applied torque has been
evaluated and can be saved.
Set the effective length.
Activate or de-activate the acoustic sig-
nal.
Activate or de-activate the vibration sig-
nal.
The counter can be activated or de-activ-
ated.
The counter can be reset.
SYSTEM
Language German
Factory setting
OK
Master PWD OFF
Settings 1/4
Select the system language.
Reset to factory settings. All data and set-
tings will be deleted.
Activate or de-activate master password.
Password is requested when opening the
menu.
Overload info
12. Interference and troubleshooting
Fault/display message Possible causes
Switches off automatically Standby set to a value that
when not being used. is too short.
Password incorrect Password forgotten or
entered incorrectly.
Tare not successful. A load was applied to the
torque wrench during the
taring process.
Recalibration required. Maximum torque of the
torque wrench exceeded
by 25 %.
Overload Maximum torque of the
torque wrench exceeded
by 40 %. For torque wrench
12 Nm at 100 %.
In the menu item "Info": Number of possible meas-
Measurements left. urements remaining until
the next recalibration.
Battery low Rechargeable battery is al-
most flat.
Configuration via mobile Torque wrench is connec-
app. ted to the app and settings
must be configured on the
smartphone.
Traceability is activated but Bluetooth connection to
there is no connection to the app not established or
the app. linked to the wrong destin-
ation device.
13. Maintenance
Frequency Maintenance work
Every 5000 tightening op- Recalibrate, adjust as ne-
erations, or every 12 cessary
months
Tab. 1: Maintenance table
14. Cleaning
Remove dirt using a soft, clean and dry cloth. Do not use chemical, alcohol-based, ab-
rasive or solvent-based cleaners.
15. Storage
Before storage, remove rechargeable battery. Store the rechargeable battery in a dry
and dust-free location at a temperature between -20°C and +25 °C and a humidity
level of less than 75%. Ensure the charge level is at 30%.
Store the torque wrench at a temperature between -20°C and +70°C and at a humid-
ity of less than 90% (non-condensing). Store in the original packaging, protected
from light, free of dust in a dry place. Do not store in the vicinity of acidic, aggressive,
chemical substances, solvents, humidity and dirt.
16. Technical data
Dimensions and general data
Size 12 30 50
3
Square ¼ inch ¼ inch /
8
drive
Socket for 9×12 mm 9×12 mm 9×12 mm 9×12 mm 14×18 mm 14×18 mm
plug-in
head
Length 355 mm 355 mm 398.5 mm 418.6 mm 535 mm
Width 45.8 mm 45.8 mm 45.8 mm
Height 38.3 mm 38.3 mm 38.3 mm
Weight 0.6 kg 0.6 kg 0.8 kg
Pre-warn- Adjustable: 50 – 99% of the minimum target value
ing
Display 2 inch TFT display
Display all occasions the maximum
torque of the torque wrench is exceeded.
Action
Change the setting under
"Settings", "Display",
"Standby".
If you forget the password:
1. Press the Right / Next /
confirm key for 5
seconds whilst the
"WRONG PASSWORD"
message is displayed.
▶ A code is displayed.
2. Contact Hoffmann
Group Customer Ser-
vice. Have the code and
serial number to hand.
1. Remove the load from
the torque wrench.
2. Repeat the taring pro-
cess.
Have recalibration carried
out.
Have recalibration carried
out.
Have recalibration carried
out.
Charge the rechargeable
battery.
Configure settings on the
smartphone.
Connect to the right des-
tination device or de-activ-
ate traceability.
Performed by
Hoffmann Group Customer
Service
100 200 340
inch ½ inch ½ inch ½ inch
655 mm
45.8 mm 45.8 mm 45.8 mm
38.3 mm 38.3 mm 38.3 mm
0.9 kg 1.4 kg 1.5 kg