Descargar Imprimir esta página

SFA Compact Serie Instrucciones De Instalación página 22

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 39
EN
5.1 USING THE TWO-POSITION SWITCH
(COMFORT MODEL)
The switch allows according to its position:
• ADD WATER: bowl flushing command,
• PUMP OUT: maceration and discharge command.
Keeping the «Pump out» position engaged allows complete
emptying of the bowl.
Sequence for the use of the switch
1/ Flush (ADD WATER): recommended water level = halfway
up the bowl,
2/ Discharge (PUMP OUT),
3/ Flush (ADD WATER) to refill the trap in WC pan.
5.2 USING THE PNEUMATIC PUSHBUTTON
(PLUS MODEL)
POWER ON
The pneumatic pushbutton can trigger 2 automatic flushing/
maceration-discharge/flushing cycles:
- Normal cycle = long flush = 1 press. Recommended for the
evacuation of solids and toilet paper.
- Eco cycle = short flush = 2 successive presses. Recommended
for the evacuation of liquid and a small amount of paper.
A long press allows complete emptying of the bowl.
5.3 USING THE ELECTRONIC BUTTON
(PREMIUM MODEL)
5.3.1 PRESET MODES
The electronic button can trigger 2 automatic flushing/
maceration-discharge/flushing cycles:
Normal Cycle
- Normal cycle: long flush. Recommended for the evacuation of
solids and toilet paper.
- Eco cycle: short flush. Recommended for the evacuation of
liquid and a small amount of paper.
A long press on the Normal Cycle button allows complete
emptying of the bowl.
5.3.2 PROGRAM MODE
To enter the programming mode
Press the "Normal" and "Eco" buttons at the same time for at
least 5 seconds. The red LED flashes for 3 seconds and then
goes out.
Programming mode
- one press on the Normal cycle button = the rinsing time
increases by 1 second.
- one press on the Eco cycle button = the rinsing time decreases
by 1 second.
The LED lights up with each press. When the modification
reaches the maximum or minimum, the LED no longer lights
up.
To exit the programming mode automatically: no keys pressed
for 5 seconds = the red LED flashes quickly for 3 seconds then
turns off.
Note: The water consumption programmed remains in the
memory even after the unit has been disconnected from the
power supply.
5.4 USING THE CONTROL PANEL (LUXE MODEL)
5.4.1 PRESET MODES
Normal Cycle
Recommended for flushing solids and
toilet paper.
Press NORMAL button.
The cycle is 15 s long.
POWER ON
POWER ON
TANK
Eco Cycle
POWER ON
Eco Cycle
Recommended for flushing liquids and
small amounts of toilet paper.
Press ECO button.
The cycle is 8 s long.
POWER ON
Empty bowl Cycle
Recommended for removing water
from the bowl.
Press EMPTY button until the water
reaches its minimum level in the bowl.
POWER ON
Note: Remains of water are always
present as it is required for the trap.
Press the NORMAL or ECO button to
return to normal operation.
Note: It is not possible to use the toilet
when the black water tank is full (see
5.4.2 PROGRAM MODE
Adjustment of the rinsing cycle: The rinsing time during the
"Normal" cycle can be programmed to increase up to 5 more
seconds. The cycle will increase from 15 to 20 seconds.
To enter the programming mode:
• Press the NORMAL and ECO buttons at the same time for
at least 5 seconds. The orange LED flashes for 5 seconds and
then goes off.
Programming
- 1 press on the NORMAL button = change to the next level
indicated by a beep. This will increase the amount of incoming
water by 1 second (5 pesses max.).
- 1 press on the ECO button = change to the previous level
indicated by a beep. This will decrease the amount of incoming
water by 1 second.
When the modification reaches the maximum or minimum
level, the buzzer stops beeping.
• To exit the programming mode automatically: no keys
pressed for 5 seconds = the orange led turns off and the green
led turns on.
Note: The water consumption programmed remains in the
memory even after the unit has been disconnected from the
power supply.
5.5 MANAGEMENT OF THE BLACK WATER TANK
5.5.1 SANIMARIN PREMIUM
When the high level sensor is activated
(high level reached),
LED flashes red: the word «TANK»
becomes visible. It is still possible to
use the water chase 3 times.
- After 3 additional flushes, the
TANK
TANK
led turns solid red and it becomes
impossible to use the flush (system
locked).
Override of the system when locked
Pressing «NORMAL» for 5 seconds will
return cycles to normal operation.
IMPORTANT
Prolonged use of the toilet when black water tank is full
can lead to overflow.
Ö Disabling the locking system is strongly discouraged.
12
POWER ON
POWER ON
).
5.5.2 Sanimarin luxe
the button

Publicidad

loading