Regulatory Agency Statements - DSC HS2016 Manual De Usuario

1 2 R e g u l a t o r y A g e n c y S t a t e m e n t s
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital
Security Controls could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio
or television reception, which can be deter-mined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Re-orient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: "How
to Identify and Resolve Radio/Television Interference Problems". This
booklet is available from the U.S. Government Printing Office, Washington
D.C. 20402, Stock # 004-000-00345-4.
The keypads represented in this manual can be used with the following
Control Units: HS2016, HS2032, HS2064, HS2128.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules and, if the product
was approved July 23, 2001 or later, the requirements adopted by the AC-
TA. On the side of this equipment is a label that contains, among other in-
formation, a product identifier. If requested, this number must be provided
to the Telephone Company.
HS2016 Product Identifier US:F53AL01BHS2128
HS2032 Product Identifier US:F53AL01BHS2128
HS2064 Product Identifier US:F53AL01BHS2128
HS2128 Product Identifier US:F53AL01BHS2128
USOC Jack: RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and mod-
ular plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. See installation instructions
for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected
to a telephone line. Excessive RENs on a telephone line may result in the
devices not ringing in response to an incoming call. In most but not all are-
as, the sum of RENs should not exceed five (5.0). To be certain of the num-
ber of devices that may be connected to a line, as determined by the total
RENs, contact the local Telephone Company. For products approved after
July 23, 2001, the REN for this product is part of the product identifier that
has the format US: AAAEQ##TXXXX. The digits represented by ## are
the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier prod-
ucts, the REN is separately shown on the label.
Incidence of Harm
If this equipment (HS2016, HS2032, HS2064, HS2128) causes harm to the
telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance notice
is not practical, the Telephone Company will notify the customer as soon as
possible. Also, you will be advised of your right to file a complaint with the
FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment. If
this happens the Telephone Company will provide advance notice in order
for you to make necessary modifications to maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment (HS2016, HS2032, HS2064,
HS2128) for repair or warranty information, contact the facility indicated
below. If-the equipment is causing harm to the telephone network, the Tele-
phone Company may request that you disconnect the equipment until the
problem is solved. This equipment is of a type that is not intended to be re-
paired by the end user.
DSC c/o APL Logistics 757 Douglas Hill Rd, Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state
public utility commission, public service commission or corporation com-
mission for information.
Alarm dialing equipment must be able to seize the telephone line and place
a call in an emergency situation. It must be able to do this even if other
equipment (telephone, answering system, computer modem, etc.) already
has the telephone line in use. To do so, alarm dialing equipment must be
connected to a properly installed RJ-31X jack that is electrically in series
with and ahead of all other equipment attached to the same telephone line.
Proper installation is depicted in the figure below. If you have any questions
concerning these instructions, you should consult your telephone company
or a qualified installer about installing the RJ-31X jack and alarm dialing
equipment for you.
Customer Premises Equipment and Wiring
Network
Service
Provider's
RJ-31X
Fac lilies
Jack
Telephone
Line
Network
Demarcation
Telephone
Point
Answering
45
Computer
Unused
Alarm Dialing
RJ-11 Jak
Equipment
Unused
Fax Machine RJ-11 Jak
System
Telephone
Telephone