Publicidad
Idiomas disponibles
Idiomas disponibles
Common Emissivity Values
Material
Aluminum (oxidized) ..................................... 0.25
Aluminum (polished) ....................................... 0.1
Asbestos
................................................... 0.95
Brass (oxidized) .............................................. 0.6
Brass (polished) .............................................. 0.1
Carbon
.................................................. 0.75
Carborundum ................................................ 0.85
Cardboard
.................................................... 0.9
Cast Iron (polished) ......................................... 0.2
Cast Iron (rusted) .......................................... 0.95
Chromium (polished) ....................................... 0.1
Concrete
..................................................... 0.7
Copper (oxidized) ............................................ 0.8
Copper (polished) .......................................... 0.05
Gold (polished) ................................................ 0.1
Iron plate
.........................................0.7 to 0.85
Lead (oxidized) ................................................ 0.3
Lead (pure) .................................................... 0.1
Marble
..................................................... 0.9
Matte black paint ........................................... 0.95
Nickel (pure) ................................................... 0.1
Nickel plate (oxidized) .................................... 0.95
Paper
.................................................... 0.9
Plaster
..................................................... 0.9
Plastics
..........................................0.8 to 0.95
Quartz
..................................................... 0.9
Red Brick
.........................................0.75 to 0.9
Rubber (rough) ............................................. 0.98
Rubber (smooth) ............................................. 0.9
Silica
.................................................... 0.4
Silver (polished) .............................................. 0.1
Stainless Steel (other) ............................ 0.2 to 0.6
Stainless Steel (polished) ................................ 0.1
Steel (ground sheet) ........................................ 0.6
Steel (Mild) ............................................0.3 to 0.5
Steel plate ..................................................... 0.9
Timber
........................................... 0.8 to 0.9
Water
.................................................. 0.98
Zinc (oxidized) ................................................. 0.1
Overloading
If the tool is overloaded for any reason the internal
electronics will cause it to stop working. This safety
feature will prevent under voltage, over temperature, and
over current damage to the tool or battery. Release the
trigger to resume operation.
The following conditions may cause temporary shut-
down of the tool as a safety feature to the user, as well as
to prolong the life of the tool and battery.
— Battery under voltage protection - The display will
flash "Lo bat" for 8 seconds indicating the battery
needs to be charged before turning off.
ZCTG861CE Rev. A
Emissivity
Battery Charging
1. If charger is supplied with a separate charger cord,
plug cord into charger.
2. Plug the other end of charger into the AC power source.
3. Insert battery pack in charger. Press lightly on battery
pack until it stops. The charger is equipped with a 4-LED
fuel gauge that indicates 25%, 50%, 75% and 100%
state of charge. When the battery makes contact, all 4
green LEDs on the fuel gauge of the charger will flash
twice and then the charger will step through the 4 LEDs
and stop at the one flashing green LED that signifies the
battery state of charge and that the battery is charging.
4. Certain built-in safety protections may lock the charger
off. If no charger light illuminates, remove the battery
and unplug the charger for 10 minutes. Plug the charger
back in and insert a known good battery. If no light
comes on the charger is faulty and must be replaced.
9
— Battery or tool over temperature - The display will
flash "Hot bat" for 8 seconds and indication the
battery is too hot and needs to be removed from
the CTG861 immediately and cooled.
Figure
2: Inserting Battery Pack
Figure
3: Inserting the Battery Pack into the Charger
(01/19)
Publicidad
