RIDGID RP 342-XL Manual página 6

RP 342-XL Press Tool RP 342-XL Press Tool
• Do not expose a battery pack or tool to fire or ex-
cessive temperature. Exposure to fire or temperature
above 265 °F (130 °C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging im-
properly or at temperatures outside the specified
range may damage the battery and increase the risk
of fire.
Service
• Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
• Never service damaged battery packs. Service of
battery packs should only be performed by the manu-
facturer or authorized service providers.
Specific Safety Information
WARNING
This section contains important safety information
that is specific to this tool.
Read these precautions carefully before using the
press tool to reduce the risk of electrical shock,
fire, explosion or serious personal injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE!
A compartment in the tool carrying case is included to
keep this manual with the machine for use by the operator.
Press Tool Safety
• Keep your fingers and hands away from pressing
attachments during press cycle. Your fingers or
hands can be crushed, fractured or amputated if they
become caught between the attachment or between
these components and any other object.
• Do not use Standard Series attachments with
tool in "Extended" configuration. This leaves a gap
between the attachment and sleeve, allowing access
to the tool rollers during use. This increases the risk of
crushing injuries.
• Never attempt to repair damaged pressing attach-
ments (jaws, press ring, actuator, etc.). Discard the
entire damaged attachment. An attachment that has
been welded, ground, drilled or modified in any man-
ner can shatter during pressing resulting in serious
injury. Failure to replace the entire pressing attachment
may result in component failure and serious injury.
4
• Large forces are generated during use that can
break or throw parts and cause injury. Stand clear
during use and wear appropriate protective equip-
ment, including eye protection.
• Only use RIDGID Press Tools with appropriate
®
RIDGID or RIDGID approved Pressing attachments
(jaws, press rings, actuators, etc.). Other uses or
modifying the Press Tools for other applications may
damage the press tool, damage the attachments and/
or cause personal injury.
• Use proper tool, attachment and fitting combina-
tions. Improper combinations can result in an incom-
plete joint, which increase the risk of leaks, equipment
damage and injury.
• Before operating a RIDGID Press Tool, read and un-
derstand:
– This operator's manual
– The attachment instructions
– The battery/charger manual
– The fitting manufacturer's installation instructions
– The instructions for any other equipment or material
used with this tool
Failure to follow all instructions and warnings may
result in property damage and/or serious injury.
RIDGID Contact Information
If you have any question concerning this RIDGID
– Contact your local RIDGID
– Visit RIDGID.com to find your local RIDGID contact
point.
– Contact Ridge Tool Technical Service Department at
ProToolsTechService@Emerson.com, or in the U.S.
and Cana da call 844-789-8665.
Description
The RIDGID RP 342-XL Press Tool, when used with ap-
®
propriate attachments, is designed to mechanically press
fittings onto tubing to create a water-tight and permanent
seal, such as for plumbing and heating applications.
When the run switch on the press tool is depressed, an
internal electric motor powers a hydraulic pump which
sends fluid into the cylinder of the tool, moving the ram
forward and applying force to the attachment, pressing
the fitting.
The press tool has two configurations that are changed by
sliding the tool sleeve. In Standard configuration, the tool
can be used with RIDGID Standard Series Press Attach-
ments. The Extended configuration allows use with com-
product:
®
distributor.
®
999-999-207.10_REV. B