Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
EasyClean brush special for gaskets
This model also includes a cleaning brush which, combined with water and soap, helps
remove stains and allows for a more efficient cleaning. When using this accessory, water will
automatically come out at low pressure.
2-spin brush special for floors
This accessory is installed on the wand of the product and consists of hard bristles. When
activated, it rotates while emitting water at high pressure, making thorough cleaning possible
in the most convenient way. It is designed to clean the patio, garden floor or floors in general.
Fig 7
Warning
This is a wand accessory, it does not fit the gun, to fit it push it in and then turn to lock.
Warning
Before using the 2-spin brush, you must check it will not damage the surface to be cleaned by
testing it on an inconspicuous place.
Warning
Do not try to assemble accessories while the pressure washer is on.
Rotary brush
This accessory is installed on the wand of the product. When activated, it spins while emitting
water at low pressure, ensuring a soft cleaning in delicate and inaccessible surfaces.
3D TurboFlip nozzle
The 3D TurboFlip nozzle, also defined as a rotating nozzle, is a very effective accessory to
significantly reduce cleaning time. It must be used to clean in the turbo mode explained in the
previous section.
Warning
Since a 3D TurboFlip nozzle uses a high-impact narrow jet, use it only with areas in which the
cleaning surface cannot be damaged. Plus, the turbo nozzle is NOT adjustable and cannot be
used to apply detergent.
Cleaning process
The following cleaning procedure will help you organise and ensure you get the best results.
Remember to follow the previous advice.
Preparing the surface
-
Clear the area of furniture and check that windows and doors are securely closed.
-
Also make sure that plants and trees near the area to be cleaned are protected with a cloth.
H Y D R O B O O S T 3200 INDUCTION PROCLEAN
68
Initial high-pressure rinse
Spray the area to be cleaned with water to clean any dirt that may have accumulated on the
surface. Start with the nozzle with less pressure and progressively increase it until reaching
the desired jet power. In this way, you will avoid applying an excessively direct jet on more
delicate surfaces.
Using soap
Water and soap must be used with these percentages: 5.4% soap, 94.6% water (1:19).
Warning
Use only soaps designed for pressure washers.
-
Test the soap in an inconspicuous place before using the product.
-
Loosen the cap of the soap bottle and fill it with water and soap.
-
Replace the cover.
-
Disassemble the wand from the gun.
-
Install the soap bottle in the gun. Fig. 6
-
Apply soap in a manner that it covers all the surface to be cleaned. Apply it from bottom to
top to avoid soap from falling down and staining the surface.
-
Leave the soap to act on the surface for several minutes. However, in particularly soiled
areas, use a brush to gently scrub. Do not allow soap to dry on the surface.
-
Remove the soap bottle from the gun and replace it with the wand and nozzle or accessory
to be used.
-
Rinse the soap from the surface.
Warning
Rinse the soap bottle with clean water after every use.
Final rinse
Start the final rinse from bottom to top. Make sure that the surface is well rinsed and that all
dirt has been removed.
Turning off
-
Make sure there is no detergent in the system.
-
Turn off the motor (place the switch in the off position).
-
Turn off the water supply.
-
Once the product and the water supply have been turned off, press the trigger to
depressurise the device.
-
Remove the water inlet hose from the pressure washer.
-
After each use, wipe the surface of the pressure washer with a clean, damp cloth.
-
Place the trigger lock.
H Y D R O B O O S T 3200 INDUCTION PROCLEAN
ENGLISH
69
Publicidad
