Descargar Imprimir esta página

Beurer MG 139 Instrucciones De Uso página 12

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 19
5. DEVICE DESCRIPTION
Battery massage cushion with heat function
The related illustrations are on page 3.
1
Heating surfaces
2
Four massage heads
Rotating in pairs
3
Mains adapter connection
Control unit
4
5
Speed indicator (2 LEDs)
During operation:
One LED lights up green = low speed
Two LEDs light up green = high speed
When charging:
LEDs flash blue alternately
One LED lights up, one flashes blue = battery level 51-99%
Both LEDs light up steady blue
ON/OFF button
6
Heat indicator (2 LEDs)
7
One LED lights up red = low heat level
Two LEDs light up red = high heat level
Heat button
8
9
Mains adapter
6. USAGE
6.1 Initial use/charging the battery
Before using the device for the first time, you must charge it for a
minimum of 2.5 hours. To do so, proceed as follows:
1. Remove all packaging material from the device.
2. Check the device, mains adapter and cable for damage.
3. Plug the supplied mains adapter
adapter connection
3
socket. The LEDs on the speed indicator
the current battery level.
LEDs flash blue alternately
One LED lights up, one flashes blue = battery level 51-99%
Both LEDs light up steady blue
4. As soon as the two LEDs of the speed indicator
blue, remove the mains adapter
is now fully charged. The battery will last for approx. 2 hours of
operation when fully charged. As soon as the speed indicator
starts to flash blue, you must recharge the device; otherwise it
will automatically switch o .
= battery level 0-50%
= battery level 100%
into the mains
9
at the side and into a suitable
will show
5
= battery level 0-50%
= battery level 100%
5
light up steady
from the socket. The battery
9
6.2 Starting use
The device comes with an automatic switch-o
function. This means that the device switches o
automatically after 15 minutes of operation.
 CAUTION
• Do not use the massage function on the massager for more
than 15 minutes. Longer massages can lead to over-stimulation
of the muscles, creating tension instead of aiding relaxation.
• Do not force or jam any part of your body, in particular your
feet, hands and fingers, between the rotating massage heads
or their holders in the device.
Massage areas
Back massage:
upper back area
Switching on
1. Press and hold the ON/OFF button
and a red LED begin to flash on the control unit
is now in standby mode.
2. Briefly press the ON/OFF button
LED of the speed indicator
massage heads will start to rotate.
3. By briefly pressing the ON/OFF button
between:
Low speed -> High speed -> Standby
4. Press the heat button
heat indicator
7
also be used without a massage. By briefly pressing the heat
button
, you can choose between:
8
Low heat (1 red LED) -> High heat (2 red LEDs).
5. At first, just press the body area that you want to massage care-
fully against the massage cushion. Then carefully check that the
massage position is comfortable for you. Now gradually shift your
body weight towards the massage cushion. The massage should
feel pleasant and relaxing at all times. If the massage is painful
5
or uncomfortable, stop the massage or change your position or
the contact pressure.
6. To switch the device o , press and hold the ON/OFF button
2 seconds. The LEDs on the control unit
12
Back massage: lower
back area (lumbar)
for 2 seconds. A green
6
to switch on the device. An
6
will start to light up green. The
5
, you can choose
6
8
to switch on the heat function. The
will start to light up red. The heat function can
will go out.
4
Leg massage
4
. The device
for
6

Publicidad

loading