Cub Cadet Pro Z SurePath Manual Del Operador página 15

C. POWER TAKE-OFF (PTO) KNOB
The PTO knob is located on the RH console to the right of the
operator's seat.
The PTO knob operates the electric PTO clutch mounted on
the bottom of the engine crankshaft. Pull the knob upward
to engage the PTO clutch, or push the knob downward to
disengage the clutch.
The PTO knob must be in the OFF position when starting
the engine.
D. HOUR METER & SERVICE MINDER (IF EQUIPPED)
The hour meter and service minder is located on the RH console to the right of the
operator's seat. It records the hours that the mower has been operated and engine
speed (RPM) in the digital display.
Hour Meter (if equipped)
The hour meter is activated whenever the ignition
switch is turned to the ON position. Keep a record
of the actual hours of operation to assure all
maintenance procedures are completed according to the
instructions in this Operator's Manual and the Engine
Operator's Manual.
Hour Meter & Service Minder with MODE Button (if equipped)
The hour meter and service minder is activated
whenever the ignition switch is turned to the ON
position. Keep a record of the actual hours of operation
to assure all maintenance procedures are completed
according to the instructions in this Operator's Manual
and the Engine Operator's Manual. The hour meter and service minder is equipped
with a MODE button that can toggle between available functions and can be used to
reset service alerts. Press and hold the MODE button for 3 seconds while in service
alert mode or when in a service alarm mode to reset.
NOTE: When the ignition key is out of the STOP position the hourglass
is illuminated/blinks to indicate it is recording the hours of mower operation,
regardless of whether the engine is started.
E. THROTTLE
Manual Throttle (if equipped)
The throttle control is located on the RH console to the right of the
operator's seat. When set in a given position, a uniform engine speed will
be maintained. The throttle control moves between the FAST
SLOW positions.
Push the throttle control handle forward to increase the engine speed. The
mower is designed to operate with the throttle control in the FAST
throttle) position when the mower is being driven and the mower deck
is engaged.
Pull the throttle control handle rearward to decrease the engine speed.
OPERATION
Electronic Throttle (E-Governor) Lever (if equipped)
The electronic throttle (E-governor) lever is used to control engine speed
and RPM's. It also helps control fuel efficiency. The electronic throttle
lever moves between the FAST
position is used for basic transportation of the mower with the
PTO disengaged and uses the least fuel. The FAST
used when the PTO is engaged and uses the most fuel. The mower should
be started in the START position, but should always be in the FAST
position when the PTO/deck is being used.
F. CUTTING WIDTH KNOB
The cutting width knob, only available when mower
is in SurePath Auto Steer Mode, is located on the RH
console to the right of the operator's seat and has four
positions. MOST EFFICIENT is suitable for most terrains
and maintains standard mowing path overlap. Turn
dial progressively from right to left if operating under
extreme conditions or if visible sections of uncut
0.0
grass occur when mower is in MOST EFFICIENT setting.
G. CHOKE KNOB (IF EQUIPPED)/MIL (IF EQUIPPED)
Choke Knob (if equipped) - The choke knob is located on the
left side of the mower next to the operator's seat. Pull the knob
out to choke the engine; push the knob in/down to open the choke.
Having the choke in the ON position helps the engine to start
during initial start-up. During normal operation the choke should
0.0
be OFF.
MIL (if equipped) - The Multifunction Indicator Light (MIL) provides diagnostic
information for the engine. If the MIL lights up and/or flashes see the service manual
or contact your service center.
H. PARKING BRAKE LEVER
The parking brake lever is located to the left of the operator's seat. When
symbol
pulled up it engages the parking brake and when pushed down it releases
the brake.
NOTE: If the forward or reverse drive pedal is engaged when engaging the
parking brake, the engine will stop. The parking brake must be placed in the
engaged position when starting the engine.
I. FORWARD DRIVE PEDAL
The forward drive pedal is located on the right side of the machine,
and
directly to the right of the steering column. Press the forward drive
pedal forward to cause the mower to travel forward. Ground speed
is also controlled with the forward drive pedal. The further forward
the pedal is pivoted, the faster the mower will travel. The pedal will
(full
return to its original/neutral position when it is not pressed.
J. REVERSE DRIVE PEDAL
The reverse drive pedal is located on the right side of the mower,
to the right of the forward drive pedal, along the running board.
Ground speed is also controlled with the reverse drive pedal. The
further downward the pedal is pivoted, the faster the mower will
travel. The pedal will return to its original/neutral position when it
is not pressed.
15
and SLOW positions. The SLOW
position should be