KitchenAid 720-0787 Instrucciones De Instalación Y Manual De Uso Y Cuidado página 28

OUTDOOR GRILL CARE
a i a ¸ e i 8 e ..... .....
If igniters stop sparking, the battery should be replaced.
1. Unscrew igniter button cap counterclockwise to remove.
A
_ S '//'
}
b
_ _AA"' _ze b_tery
B_l_er cap
B
2. Remove battery from the battery compartment.
3. Replace with a new alkaline "AA" size battery. Install
battery with negative end in first.
4. Screw igniter button cap clockwise into place.
IMPORTANT: Before cleaning, make sure all controls are off and
the grill is cool. Always follow label instructions on cleaning
products.
For routine cleaning, wash with soap and water using a soft cloth
or sponge. Rinse with clean water and dry at once with a soft,
lint-free cloth to avoid spots and streaks.
Do not use steel wool to clean the grill, as it will scratch the
surface.
To avoid weather damage to finish, use grill cover.
STAINLESS STEEL
IMPORTANT: To avoid damage to stainless steel surfaces, do
not use soap-filled scouring pads, abrasive cleaners, cooktop
polishing creme, steel wool, gritty wash cloths or paper towels.
Cleaner should not contain chlorine. Damage may occur. Food
spills should be cleaned as soon as entire grill is cool. Spills may
cause permanent discoloration.
Cleaning Method:
• Rub in direction of grain to avoid scratching or damaging the
surface.
• Stainless steel cleaner.
• Liquid detergent or all-purpose cleaner.
• Rinse with clean water and dr with soft, lint-free cloth.
• Vinegar to remove hard water spots.
• Glass cleaner to remove fingerprints.
GRILL GRATES
IMPORTANT: To avoid damage to grill grates, do not use a
steel or fiber scraper. Immediately after you are finished cooking,
loosen food soil with a brass bristle brush. Turn all burners to
HIGH for 10-15 minutes with the hood closed to burn off food
soil. Turn off all burners, raise the hood and let grates cools. Use
the brass bristle brush to remove ash from the grill grates.
When completely cool, grill racks can be removed for thorough
cleaning. Clean them with a mild detergent and warm water.
For baked-on soil, prepare a solution of 1 cup (250mL) ammonia
to 1 gal. (3.75 L) water. Soak grates for 20 minutes, then rinse
with water and dry completely.
WARMING SHELF
Cleaning Method:
• Liquid detergent or an all-purpose cleaner.
• Rinse with clean water and dry with soft, lint-free cloth.
• For tough spots or baked-on grease, use a commercial
heavy duty degreaser designed for stainless steel.
IMPORTANT: Make sure gas supply is off and all control knobs
are in the OFF position.
EXERIOR
The quality of this material resists most stains and pitting,
providing that the surface is kept clean, polished and covered.
• Apply stainless steel polish to all non-cooking areas
before first use. Reapply after each cleaning to avoid
permanent damage to surface.
• Cleaning should always be followed by rinsing with
clean warm water.
• Wipe the surface completely dry with a soft cloth.
• For tough spots or baked-on grease, use a commercial
heavy duty degreaser designed for stainless steel.
INTERIOR
Discoloration of stainless steel on these parts is to be expected,
due to intense heat from the burners. Always rub in the direction of
the grain. Cleaning should always be followed by rinsing with clean,
warm water.
Cleanin.q Method:
• Liquid detergent or all-purpose cleaner.
• Rinse with clean water and dry completely with a soft, lint-
free cloth.
• A heavy-duty scrub sponge can be used with mild
cleaning products.
• For small, difficult-to-clean areas, use a commercial heavy
duty degreaser designed for stainless steel.