Publicidad
Idiomas disponibles
Idiomas disponibles
GB
RANGER
RANGER
Height: 40-150 CM
Weight: 0-36 KG
i-Size booster seat Enhanced Child Restraint System
3.1
USAGE
3.1- Install position of the child seat in vehicle
A
Shoulder belt
B
Lap belt
C
ISOFIX anchorages
Proper installation
Improper installation
Only suitable if the approved vehicles are fitted with 3 point safety-belt, approved to UN/ECE Regulation No.16
or other equivalent standards.
"
"ISOFIX Anchor points for car seats
Not to use in seating positions where an active frontal airbag is installed.
Only use on this seat if ISOFIX anchorages are fitted.
3. 2- Adjust the headrest
As shown in the picture, you can adjust the headrest up and down by pulling on the headrest adjustment tab
(1)
, and adjust the headrest to a position suitable for the child's head.
3. 3- Checking the shoulder strap height
Always check that the shoulder straps are at the correct height for your child. The child's shoulder straps should
always be threaded through the slots in the cover and seat shell that are closest to the top of your child's
shoulders.
3. 4- Usage of buckle
(8)
Get the left and the right pieces of buckle together.
Insert the two pieces into the slot of the buckle .At the same time, hearing "click" means the buckle gets stuck,
pull the pieces of the buckle and check whether the buckle is locked correctly.
* If you want to release the safety belts, it needs to press the red button, then the pieces pop up.
3. 5- Adjust the length of harness
Loosen the harness
(14)
The harness can be slackened by pressing
the adjuster(under the seat cover
(11)
on the front of the seat. Press down the adjuster as you grip the two
harness with your another hand. Pull the harness towards you to loosen the harness.
Tighten the harness
(14)
Pull the harness upward to remove the slack from the lap sections of the harness then pull the front stretch belt
until the harness is fully tightened.
* The harness should be adjusted as tightly as possible without causing discomfort to your child. A loose
harness can be dangerous.
* Check the harness adjuster and tighten each time when the child is placed in the seat.
3. 6- The method to store shoulder straps with chest pad and buckle
* Suitable for children in height 105-150cm.
20
GB
RANGER
(1, 2, 3)
Storage of buckle
(4, 5, 6)
Storage of shoulder straps and sleeves
1) Press red button to release the buckle
(8)
2) Take the buckle out of the crotch pad;
3) Then lift the seat cover, pull out the buckle from the cover hole, and put it into the seat groove for storage;
4) Tear the Velcro of the two shoulder sleeves
(5)
sleeves;
5) Loosen the snap button on both sides of the headrest cover to expose the internal structure of the seat, and
store the sorted shoulder sleeves in the grooves inside the seat, as shown in 6.
3. 7- Usage of the support leg
When child height in 40-105cm, the support leg is in the usage state
-Lift the bottom of the seat and push the support leg
-Push it to the front end and then take the support leg (19), out, let it is perpendicular to the ground and hear
a sound of "click" .
-The method to adjust the length of the support leg (19):
Press and hold the adjustment button on the support leg (15), then adjust the length up and down until it hits
the car ground. The bottom of the support leg will turn green.
* When child height in 105-150cm, the support leg is in the stowed state. Note: When puting away the support
leg, press and hold the bottom support leg first to prevent loosening, and push the front end of the support
leg in at the same time.
3. 8- Adjust the ISOFIX attachments
(20)
First install the two ISOFIX guide sleeves to the ISOFIX attachment of the vehicle (If your vehicle seat
is equipped with ISOFIX guide sleeves there is no need to install it).
* After installed the ISOFIX chuck, push the child restraint forwards until it is tight against the car seat. Now,
the ISOFIX base is installed in place.
The ISOFIX attachments can be adjusted for many positions to fit the different positions of ISOFIX
anchorages expending from car seat.
Press down the release button
(17)
to adjust ISOFIX attachment of both sides to the longest. Snap the ISOFIX
into the ISOFIX guide sleeve, Make sure that you have heared a "click" and the ISOFIX latching indication shows
GREEN.
If you want to release the ISOFIX attachments, just installation of the ISOFIX attachments is finished.
Push the red release button of the ISOFIX chuck at the direction as shown, the ISOFIX chuck will be released. .
3. 9-The method of rotate seat
Find the rotation adjuster butto 13, lift up and rotate the body at the same time (both sides can be rotated).
When you hear a sound of "click", the rotation adjuster automatically retracts, indicating that the gear is in
place.
A
Forward-facing 76-150cm, Weight: 9-36KG, Rotate to adjust before effect
B
90° hover Note: This status can only be used when install the child. Do not keep this state when driving.
C
Rearward-facing 40-105cm, Weight: 0-18KG, Effect after rotation adjustment.
3.10- Usage of reclining system
Find the angle adjuster (12), lift up and adjust the seat angle forward or backward at the same time.
A
Rearward-facing, 40-105cm, 0-18KG, Adjust to Gear R
B
Forward-facing, 76-105cm 9-18KG, Adjust to Gear 01/02/03/04/05/06, 105-150cm, 15-36KG, Adjust to Gear 01
put the buckle inserts in order and store them in the shoulder
(19)
forward from the groove with your hand;
(16)
low
21
Publicidad
