Hendi 204962 Manual Del Usuario página 15

paint, aerosol cans with a flammable propellant, flammable
or explosive substances, etc. inside or near the appliance.
• Once installed, the appliance must not be tilted at an angle
greater than 5° and it is necessary to wait 2h before connect-
ing it to the power supply to switch it on. The same applies if
the appliance is moved afterwards.
• If the appliance has been switched off or disconnected from
the power supply, it is necessary to wait 5 minutes until
switching on again.
• No other appliances should be plugged into the same socket
as with this appliance.
• Do not attempt to climb onto the appliance.
Intended use
• This appliance is intended to be used for commercial applica-
tions, for example in kitchens of restaurants, canteens, hos-
pital and in commercial enterprises such as bakeries, butch-
eries, etc., but not for continuous mass production of food.
• The appliance is designed for aging meat only. Any other use
may lead to damage of the appliance or personal injury.
• Operating the appliance for any other purpose shall be
deemed a misuse of the device. The user shall be solely liable
for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Main parts of the product
(Fig.1 on page 3)
1. Display panel
2. Water tank
3. Door Lock
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Spare parts or accessories
(Fig.1 on page 3)
4. UVC light
5. Activated charcoal filter
6. Absorbent Cotton
7. Stainless steel hanging rod
8. Stainless steel hook
9. Stainless steel shelf
10. Salt tray
Control panel
(Fig.2 on page 4)
11. Power Switch. Power-on State: Press on hold for 3 seconds
to switch ON./ OFF the appliance.
12. Function Key: Use this key to select the required function:
temperature set or humidity set.
13. Light/Fahrenheit/Celsius: Short press it once switch ON /
OFF the inner light.
Long press for 3 seconds: switch ON / OFF the inner light
and then display screen will be converted to Celsius or
Fahrenheit degrees.
14. Up button
15. Down button
16. UV system control
17. Temperature Display / Error code left window: to show the
current temperature and setting temperature. For Error
code issue please refer to Error code identification section
18. Humidity Display / Error code right window: to show the
current humidity and setting humidity. For Error code issue
please refer to Error code identification section
Circuit diagram
(Fig.3 on page 4)
A. Compressor
B. Veriable speed oard
C. Out fan
D. In fan 1
E. In fan 2
F. In fan 3 (only 204962 & 201433)
G. In fan 4 (only 204962 & 201433)
H. PCB board
I. Sensor 1
J. Humidifier sensor
K. Rectifier
L. UVC
M. Heater
N: Door light switch
O. Electronic expansion valves
P. Display board
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
GB
15