Maintenance And Inspection - HIKOKI C 3607DRA Instrucciones De Manejo

English
By connecting with dust extractor through adapter,
joint and dust collection adapter, most of dust can be
collected.
Connect the dust extractor with adapter.
(1) Connect in order of hose (id 38 mm × 3 m long) and
adapter (Dust extractor's Standard accessory) joint
(Optional accessory) and dust collection adapter
(Optional accessory) with the duct of power tool.
Connection is done by pressing in the direction of the
arrow. (Fig. 31)
The dust collection adapter (Optional accessory) is fi xed
to the duct by a hose band. (Optional accessory)
21. Using the LED light (Fig. 32)
Safeguard Function
Overburden Protection
Temperature Protection
MOUNTING AND DISMOUNTING SAW
BLADE
WARNING
To prevent an accident or personal injury, always turn
off the trigger switch and disconnect the battery from the
power tool before removing or installing a saw blade.
1. Mounting the saw blade (Fig. 33)
(1) Press in spindle lock and loosen left hex. 7 mm socket
bolt with 5 mm hex. bar wrench (standard accessory).
Since the left hex. 7 mm socket bolt is left-hand threaded,
loosen by turning it to the right.
NOTE
If the spindle lock cannot be easily pressed in to lock the
spindle, turn the left hex. 7 mm socket bolt with 5 mm
hex. bar wrench (standard accessory) while applying
pressure on the spindle lock.
The saw blade spindle is locked when the spindle lock is
pressed inward.
(2) Remove the bolt and washer (B)
(3) Lift the lower guard and mount the saw blade.
WARNING
When mounting the saw blade, confi rm that the rotation
indicator mark on the saw blade and the rotation direction
of the gear case are properly matched.
(4) Thoroughly clean washer (A) and the left hex. 7 mm
socket bolt, and install them onto the saw blade spindle.
(5) Press in the spindle lock and tighten the left hex.
7 mm socket bolt by turning it to the left by standard
accessories (5 mm hex. bar wrench).
CAUTION
○ A dust guide is installed inside behind the hinge. When
removing or installing the saw blade, do not make
contact with the dust guide. Contact may break or chip
saw blade tips.
○ Tighten the left hex. 7 mm socket bolt so it does not
come loose during operation.
○ Confi rm the left hex. 7 mm socket bolt has been properly
tightened before the power tool is started.
○ Confi rm that the lower guard has closed position.
2. Dismounting the saw blade
Dismount the saw blade by reversing the mounting
procedures described in paragraph 1 above.
The saw blade can easily be removed after lifting the
lower guard.
CAUTION
Never attempt to
180 mm in diameter.
LED Light Display
On 0.1 second/off 0.1 second
On 0.5 second/off 0.5 second
install saw blades
LED LIGHT WARNING SIGNALS
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
pulled, if any of the safeguard functions are triggered
during operation, the LED light will blink as described in
Table 3. When any of the safeguard functions are triggered,
immediately remove your fi nger from the switch and follow
the instructions described under corrective action.
Table 3
Remove the cause of the overburdening.
Allow the tool and battery to thoroughly cool.
HOW TO RECHARGE USB DEVICE
(UC18YSL3)
(1) Select a charging method
○ Charging a USB device from a electrical outlet
(Fig. 34-a)
○ Charging a USB device and battery from a electrical
outlet (Fig. 34-b)
(2) How to recharge USB device (Fig. 35)
(3) When charging of USB device is completed (Fig. 36)
TRANSPORTATION OF THE MAIN
BODY
The vice assembly could be dropped during transportation.
Either remove the assembly or slip a piece of wood between
the vice to fi rmly secure it. (Fig. 37)
Drop the head and insert the locking pin (see page 30
"Releasing the locking pin").
Turn and loosen the side handle, turn the turntable as far
right as it will go, and secure the turntable by turning the
handle to the fi xed position.This will make the main body
even more compact.
When transporting the main body, carry it in your arms,
holding the grip located on the base with both hands or carry
handle.

MAINTENANCE AND INSPECTION

WARNING
To avoid an accident or personal injury, always confi rm
the trigger switch is turned OFF and that the battery
has been disconnected from the power tool before
performing any maintenance or inspection of this tool.
Report to qualifi ed person as soon as possible, if you
discover the fault of machine including guards or blade
saw.
1. Inspecting the saw blade
Always replace the saw blade immediately upon the fi rst
sign of deterioration or damage.
A damaged saw blade can cause personal injury and
a worn saw blade can cause ineff ective operation and
possible overload to the motor.
except
34
Corrective Action