Publicidad
Idiomas disponibles
Idiomas disponibles
8.1.1
Adjust the position of the lower
push bar (4) (Fig. 5)
Notes:
Three positions are possible.
Make sure that the teeth mesh.
1. Loosen the two clamping levers (4b).
2. Loosen the two clamping levers (4b) by turning
them anti-clockwise.
3. Move the lower push bar (4) to the desired position
(use the markings as a guide).
4. Close the lower push bar (4) again (see 8.1).
8.2
Installation of the upper push bar
(2) (Fig. 6, 7)
1. Screw the upper push bar (2) to the lower push bars
(4) with one flat head screw (2a), a washer (2b), a
cylindrical nut (2d) and a quick-clamp lever (2c) on
each side.
Two positions are possible.
2. Lock the two quick-clamp levers (2) by pressing
them in the direction of the upper push bar (2).
They must rest against the upper push bar (2) in
such a way that they can be tightened with moder-
ate force.
Otherwise, the quick-clamp levers (2b) must be
turned clockwise to tighten them or anti-clockwise to
loosen them.
8.3
Fitting the cable holder (9) (Fig. 1,
8)
1. Clip the two cable holders (9) into the upper push
bar (2) and lower push bar (4) and secure the cable
(10).
8.4
Fit the carry handle (5a) to the
grass collection basket (5) (Fig.
9)
1. Attach the carrying handle (5a) of the grass collec-
tion bag (5) to the holder provided on the top of the
grass collection bag (5).
9
Pre-commissioning
NOTE
Some noise pollution from this product is
unavoidable. Postpone noisy work to ap-
proved and designated times. If necessary,
adhere to rest periods and limit the dura-
tion of work to the bare minimum.
For your personal protection and the pro-
tection of nearby persons, wear suitable
hearing protection.
32 | GB
9.1
Setting the cutting height
(Fig. 10)
ATTENTION
The cutting height may only be adjusted
when the engine is shut off.
• In dense, tall grass, set the highest cutting level and
mow more slowly. A high cutting height should be
selected for the first cut of the season. Adjust the
cutting height so that the product is not overloaded.
• Set the cutting height depending on the actual
length of the lawn.
• Carry out several passes so that a maximum of 4
cm of lawn is removed at a time.
6 different cutting heights can be set:
Ornamental lawn
1 =
2 =
3 =
The cutting height is adjusted via the cutting height ad-
justment lever (6).
1. Pull the cutting height adjustment lever (6) out-
wards.
2. Move the cutting height adjustment lever (6) to the
desired position.
3. Release the cutting height adjustment lever (6)
again. The lever locks into the desired position.
9.2
Inserting/removing the batteries
(17) into/from the battery mount
(Fig. 11, 12)
Inserting the battery
1. Open the cover (7).
2. Slide the batteries (17) into the battery mounts. The
batteries (17) click into place audibly.
3. Close the cover (7).
Removing the battery
1. Open the cover (7).
2. Press the unlock button (18) for the batteries (17)
and remove them from the battery mounts.
3. Close the cover (7).
9.3
Preparing the area to be mowed
1. Before mowing, carefully examine the area.
2. Remove stones, sticks, bones, wires, toys and other
objects that may be ejected by the product.
3. Ensure that no other people are present on the sur-
face to be mowed.
www.scheppach.com
Utility lawn
25 mm
4 =
35 mm
5 =
45 mm
6 =
55 mm
65 mm
75 mm
Publicidad
