DeWalt DWE402N Manual De Instrucciones página 12

ENglish
Edge Grinding and Cutting (Fig. I)

WARNING: Do not use edge grinding/cutting wheels for
surface grinding applications because these wheels are not
designed for side pressures encountered with surface grinding.
Wheel breakage and injury may result.

CAUTION: Wheels used for edge grinding and cutting
may break or kick back if they bend or twist while the tool is
being used. In all edge grinding/cutting operations, the open
side of the guard must be positioned away from the operator.
NOTICE: Edge grinding/cutting with a Type 27 wheel must
be limited to shallow cutting and notching—less than
13 mm in depth when the wheel is new. Reduce the depth of
cutting/notching equal to the reduction of the wheel radius
as it wears down. Refer to the Accessories Chart for more
information. Edge grinding/cutting with a Type 1/41 wheel
requires usage of a Type 1 guard.
1. Allow the tool to reach full speed before touching the
tool to the work surface.
2. Apply minimum pressure to the work surface, allowing
the tool to operate at high speed. Grinding/cutting rate is
greatest when the tool operates at high speed.
3. Position yourself so that the open-underside of the
wheel is facing away from you.
4. Once a cut is begun and a notch is established in the
workpiece, do not change the angle of the cut. Changing
the angle will cause the wheel to bend and may cause
wheel breakage. Edge grinding wheels are not designed to
withstand side pressures caused by bending.
5. Remove the tool from the work surface before turning
the tool off. Allow the tool to stop rotating before laying
it down.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power source
before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can
cause injury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk of eye
injury, always wear ANSI Z87.1 approved eye protection when
performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the plastic materials used in these
parts. Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any part
of the tool into a liquid.
Accessories

WARNING: Since accessories, other than those offered by
D WALT, have not been tested with this product, use of such
e
accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should
e
be used with this product.

WARNING: Accessories must be rated for at least the
speed recommended on the tool warning label. Wheels and
other accessories running over their rated accessory speed
may fly apart and cause injury. Threaded accessories must
have a 5/8"-11 hub. Every unthreaded accessory must have
a 7/8" (22 mm) arbor hole. If it does not, it may have been
designed for a circular saw and should not be used. Use only
12
the accessories shown in the Accessories Chart of this
manual. Accessory ratings must always be above tool speed
as shown on tool nameplate.

WARNING: Do not use a bonded abrasive wheel that is
past its expiration (EXP) date as marked near center of wheel,
if provided. Expired wheels are more likely to burst and cause
serious injury. Store bonded abrasive wheels in dry location
without temperature or humidity extremes. Destroy expired or
damaged wheels so they cannot be used.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including power
cord repairs, brush inspection and replacement) should
be performed by a D WALT factory service center or a
e
D WALT authorized service center. Always use identical
e
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRANTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with your product.
• CONFiRMATiON OF OWNERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration of
ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification is
required under the Federal Consumer Safety Act.
• Register online at www.dewalt.com.
Three-Year Limited Warranty
For warranty terms, go to https://www.dewalt.com/
support/warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D WALT Industrial Tool Co., 701 East
e
Joppa Road, Towson, MD 21286 or call 1-800-4-D
(1-800-433-9258).
lATiN AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country-specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARNiNg lABEl REPlACEMENT: If your warning
labels become illegible or are missing, call 1-800-4-D
(1-800-433-9258) for a free replacement.
WALT Industrial
e
WALT
e
WALT
e