Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE
INSTALLING
Important
Please ensure that you thoroughly check the product upon receipt
since we cannot accept responsibility for any damage reported af-
ter installation. Should you find any damage, please immediate-
ly notify the forwarder.
WE RECOMMEND CHECKING THAT ALL THE ARRANGE-
MENTS COMPLY WITH THE INSTRUCTIONS FOR PRE-
INSTALLATION.
I Unpack the bath and lift it only by the rim and never by any pipe
line or electric equipment (use protective gloves).
I Check for any damage or defects by removing the pro-
tective plastic film (damages from impact or scratches re-
ported after installation are not covered by our guarantee).
I Check that the clamps holding the rubber couplings
and the air lines are tightly fastened.
I The installation of the whirlpool baths can be made against fin-
ished (tiled) walls and floor.
The panels allow access to electromechanical devices in-
stalled under the bath rim, as well as proper aeration re-
quired for water-air mixture during hydromassage.
Aeration must be guaranteed also if Jacuzzi
not used (see "Instruction for pre-installation"). Panels
must be firmly installed and proper tools must be used
when being removed. Openings, holes, grids, used for
aeration, should not allow the introduction of objects
having a diameter of 12 mm or larger.
PRELIMINARY OPERATIONS
i
I (
1 ) Place the tub in its location of installation. Level it and
adjust the height by manually turning the feet (A) located on
i
the corners of the tub (
The upper level of the tub, measured at the end of the
NOTE:
edge, must be at a height of 60 cm from the floor. To com-
pensate for possible irregularities of the floor, the bath feet
can be regulated from -0,5 + 1 cm
DO NOT TOUCH BLOCKING NUTS (G) MARKED WITH A
RED ARROW STICKER (
i
I (
2 ) Mark on the floor a hole for each outer foot. One hole
is enough.
Remove the bath and drill the floor.
Insert screw anchors (B). Adjust center feet (A1) so they rest
i
firmly on the floor (
If the tub calls for installation of Jacuzzi
the edge of the bath, install them (
is positioned and secured in its location of installation.
®
1 ).
i
2 ).
1 ).
®
tap fixtures on
i
5 ) before the tub
i
I (
3 or 4, depending on the model ) At this stage, assem-
ble the drain column and connect it with a siphon, preferably a
plastic one.
If filling of the tub takes place via the column (dis-
pensed form overflow) you will need to install a specif-
ic DB-type protection unit (standard EN 1717), located
at least 15 cm above the edge of the tub. Concerning
system methods, we recommend you contact your wa-
ter company and/or your plumber.
I Before fixing the bath to the floor, a final test for possible wa-
ter leaks caused by transport damage should be made. Fill the
bath up to approx. 5-6 cm. above the uppermost hydromas-
sage jets.
Please make sure that all joints and fittings are thoroughly in-
spected, before emptying the tub.
i
I (
2 ) Drain the bath and secure all outer feet with screws
(C) to the floor.
i
(
1 ) Adjust center feet (A1) so they rest firmly on the floor.
I Connect the electrical box to the network and earth
system, following the electrical diagram and the direc-
tives contained in the chapter "Electrical Safety".
ASSEMBLING THE TAPS AND FITTINGS
(if included)
i
(
5
)
ATTENTION: the position of the water outlet varies
depending on the type of tub.
I Take the box that holds the various components of the taps
panels are
and fittings.
NOTE: assembly of the taps and fittings must be done
with the tub outside of the place of installation and be-
fore it is fastened to the floor.
i
I
(
) (1) Unscrew the headless screw. Slide out the cylin-
6
der of the tub filler (2); (3) then tighten ring nut "A" and ring
nut "B", and finally install the gasket "C".
NOTE: keep the headless screw.
i
I
(
7)
dicated hole and tighten the coupling from above with the o-rings.
i
I
(
) (1) By means of the coupling and the ring nut (2), tem-
8
porarily fasten the cylinder, ensuring that it is parallel with the
tub edge (3).
i
I
(
) Install on a tap the same units used for the cross
9
cylinder. Repeat the operation for the other tap.
i
I
(
10
dicated holes and tighten from above the ring nuts with the
o-rings
i
I
(
11
) By means of the respective ring nuts temporarily fas-
ten the taps, turning one with respect to the other, so as to
make it easier to install the flexible hoses (3).
i
I
(
12
from above using the ring nuts (2).
7
F rom under the tub edge, insert the cylinder in the in-
) From under the tub edge, insert the taps in the in-
) (1) Install the covers as shown, and fasten them
Publicidad
Tabla de contenido
