Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
i
I
(
) Install the shower support by placing the indicated
13
gasket.
i
I
(
) From beneath the tub edge, apply another gasket and
13
attach it with the indicated nut.
i
I
(
) Take shower hose (fittings 1/2"-3/8") and insert them
14
in the following components (from the side of the 3/8" fitting):
button E - ring nut F - rosette G - threaded tube H - Teflon
washer I (internal ø 23,3 mm) - threaded tube J - spring K
- Teflon washer L (internal ø 26 mm) - gasket M (the brass
part must face downwards)
i
I
(
15
) Fasten the flexible hose of 1/2" M-F (provided) to
the cross cylinder and run it through the inside of the show-
er support, placing it over the tub edge.
i
I
(
) (1) From above the tub edge, connect the shower
16
hose to the hose you just installed, placing the gasket. (2) Line
up washer L and gasket M inside the shower support.
i
I
(
) Screw the threaded tube J all the way into the show-
17
er support.
i
I
(
) (1) Tighten washer I onto threaded tube H and place
18
the latter on spring K inside the threaded tube J (2).
i
I
(
) Place rosette G in contact with the tub. Then screw
19
on ring nut F and finally button E on the threaded tube H.
i
I
(
20
) Run the flexible hose under the tub edge and screw in
the shower head, placing the gasket.
Use of the shower head
i
(
20
) To remove the shower head from its support, press the
ring nut down (1) and turn it about 45° (2), in order to release
the hose.
After use, put the shower head back in place, press the ring nut
and turn it about 45°.
i
I
(
) Press the water supply outlet into place as shown,
21
and fasten it from behind with the headless screw that was
i
(
previously removed.
i
I
(
) (1) After inserting the gasket, screw the flexible
22
hose1/2" F-F (included) into the indicated tap (2).
(3) Then screw the other end of the flexible hose into the cross
cylinder, as shown.
i
I
(
23
) Follow the same procedure to install the other flex-
ible hose.
i
I
(
24
) Then permanently attach, from under the tub edge, the
shower head support and the ring nuts with the screws (
i
I
(
25
) (1)Install the two pins on the shafts of the taps; (2)
turn them until the taps are in the "closed" position and fas-
ten them with hex screws(3).
i
I
(
) (1) Place the knobs on the shafts and fasten them
26
as shown (2). Finally, screw on the chromed pin (3).
) .
1
i
I
(
) Finally, make the equipotential connection, con-
27
necting the yellow-green cable (from the terminal located n-
ear the pump) to the indicated faston.
WATER CONNECTION
Filler/overflow assembly
i
I (
28 ) The connection must be made of the mixed water
pipe (see pre-installation diagram) to the outlet of the drain
column. The column has two 1/2" diameter inputs, of which
one is plugged. If necessary the plug (D) may be moved from
one input to the other, depending on the type of installation
Note: if a metal drain column is used (other than the one
provided) it must be connected to the equipotential contact
(see chapter on ELECTRIC SAFETY).
ASSEMBLY OF ACCESSORIES
i
I
(
29 ) Secure the suction cover, supplied with an O-ring, by
tightening the screw
i
I
(
30 ) In models with hydromassage, you may install as you
wish the rotating jets (Twist Jet) or the directional ones (Hy-
dro Jet) as shown:
(Twist Jet): insert the nozzle in the outlet body. Then install
the cover so that the pin fits into the centre hole of the nozzle.
(Hydro Jet): insert the plastic spring in the outlet body. Then
set the nozzle on and install the cover.
Make sure that the grooves under the cover are inserted into the
corresponding notches in the outlet unit.
i
I
(
31 ) In models with an air bubble generator (blower),
press the covers into the jets on the bottom of the tub.
I Run a hydromassage cycle, making sure that there is no
leakage, particularly in the hydraulic connections and drain.
INSTALLING THE PANELS
i
I (
32 ) Fasten the elastic metallic supports (L), using the two self-
threading screws, to the inserts (N) under the edge of the tub.
i
I (
33 ) Click the springs (P) onto the legs at the corners of
the tub and make them slide up until they touch the top, push-
ing them from both sides so that they settle inside the tub
*
).
edge.Insert the ring (R) into the groove of the leg.
i
I (
34, 35, 36, 37, 38 ) Adjust the brackets (Z) as shown, de-
pending on the model to be installed. Make sure that the brackets
are as parallel as possible with the edge of the tub (dotted line in
figure).
Adjust their height with the ring nut (Y) and their distance from
the projection of the tub edge.
Tighten the nut (W).
8
Publicidad
Tabla de contenido
