cecotec Bolero DressCode 9410 Inverter Steel A Manual De Instrucciones página 33

ENGLISH
B. Factory state
Lock nuts on the bottom of the washing machine
Levelling feet fitted to the lock nuts
Note:
The levelling feet do not come fully fixed for easier installation, so be sure to fix all four before
levelling the washing machine.
1. When positioning the washing machine, you should check if the levelling feet are fully
fixed; if not, fix them. The lock nuts must be firmly locked to the bottom of the appliance
and the levelling feet securely locked into the lock nuts. Fig. 7
2. Once the washing machine is installed, press on the opposite corners of the top with both
hands in succession and shake the washing machine vertically downwards to check if the
levelling feet are firmly fixed and that the washing machine does not wobble. Fig. 8
3. If the washing machine wobbles, loosen the lock nut in the direction shown in Figure 9
with the spanner provided until the machine is level and no longer wobbles. Fig. 9
4. Finally, use the spanner to fix the lock nut to the bottom of the washing machine (you can
also fix the levelling feet lightly by hand to prevent them from moving). Make sure the
levelling feet do not move. Fig. 10
WARNING
1. The washing machine must be perfectly level and stabilised when all four feet are firmly
on the floor.
2. Incorrect levelling adjustment may cause loud noises, vibrations of the washing machine,
shifting of the washing machine, and other abnormal occurrences.
3. The air vent is located at the bottom of the washing machine (to avoid obstructions).
Install the washing machine on a solid, smooth, non-slip floor. Do not place the washing
machine on a soft carpet or wooden floor or on top of furniture, as this may cause
unnecessary injury.
4. OPERATION
Installing the washing machine
Connecting the water inlet hose to a threaded tap. Fig. 11
1. Connect the inlet hose to the tap and fix it by turning it counterclockwise.
2. Connect the other end of the inlet hose to the inlet valve on the back of the washing
machine and secure it firmly clockwise.
3. Open the tap and check for water leaks. If they occur, repeat the process again.
64
Bolero Dresscode 7410 Inverter A / Bolero DressCode 7410 Inverter Steel A
Bolero Dresscode 8410 Inverter A/ Bolero DressCode 8410 Inverter Steel A
Bolero Dresscode 9410 Inverter A/ Bolero DressCode 9410 Inverter Steel A
Bolero Dresscode 10410 Inverter A/ Bolero DressCode 10410 Inverter Steel A
Connecting the water inlet hose to a non-threaded tap (only for certain models) Fig. 12
1. Remove adapter (A) from hose.
2. Use a Phillips screwdriver (not included) to remove the 4 screws from the adapter.
3. Hold the adapter and turn the part (C) clockwise to loosen it by approx. 5 mm (*).
4. Insert the adapter into the tap and tighten the screws until they are secure.
5. Turn the part (C) counterclockwise to fix it.
6. While pulling down part (D) of the hose, connect it to the adapter. Then, release part (D).
The hose should snap into the adapter with a "click" sound.
7. To complete the hose connection, see points 2 and 3 of the previous section (Connecting
the water inlet hose to a threaded tap).
8. Open the tap and check for water leaks. If they occur, repeat the process again.
Note:
- Do not bend the hose.
- Check the inlet hose connection before every use.
Connecting the drain hose
- The drain hose should be placed at a height of 65-100 cm above the ground, otherwise it
may cause poor drainage. Fig. 13
- You can use the supplied drain-hose bracket (depending on the model) to connect the
drain hose to the wall, drain pipe, or sink. Fig. 14
- Make sure that all hose connections are tight.
Note:
Do not immerse the end of the drain hose in water for the washing machine to work properly.
Electric connection
- Since the maximum current flow is 10 A when the interior temperature of the washing
machine increases, make sure that the power supply system (current, supply voltage, and
cord) in your home can meet the normal load requirements of electrical appliances.
- Connect the appliance to a properly installed and earthed outlet.
- Make sure that the household supply voltage matches the rated voltage of the washing
machine.
- Make sure the power plug matches the socket.
- Do not use multipurpose plugs, sockets, or extension cords.
- Do not connect or disconnect the plug with wet hands.
- When disconnecting the plug, hold it firmly and pull it out. Do not pull the power cord out
abruptly.
Warning:
1. The washing machine must be properly earthed. If a short circuit occurs, earthing can
reduce the risk of electric shock.
Bolero Dresscode 7410 Inverter A / Bolero DressCode 7410 Inverter Steel A
Bolero Dresscode 8410 Inverter A/ Bolero DressCode 8410 Inverter Steel A
Bolero Dresscode 9410 Inverter A/ Bolero DressCode 9410 Inverter Steel A
Bolero Dresscode 10410 Inverter A/ Bolero DressCode 10410 Inverter Steel A
ENGLISH
65