Hitachi Koki C 13U Instrucciones De Manejo página 6

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

PRECAUTIONS ON USING CIRCULAR SAW
1.
Do not use saw blades which are deformed or
cracked.
2.
Do not use saw blades made of high speed steel.
3.
Do not use saw blades which do not comply with
the characteristics specified in these instructions.
4.
Do not stop the saw blades by lateral pressure
on the disc.
5.
Always keep the saw blades sharp.
6.
Ensure that the safety cover moves smoothly and
freely.
7.
Never use the circular saw which its safely cover
fixed in the open position.
SPECIFICATIONS
Voltage (by areas)*
Cutting Depth
Power Input*
No-Load Speed
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Saw Blade (Dia. 335 mm) ......................................... 1
(2) Wrench ....................................................................... 1
(3) Guide .......................................................................... 1
(4) Wing-bolt ................................................................... 1
(5) Riving knife ................................................................ 1
(6) Hexagon head bolt .................................................... 2
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORY (sold separately)
Dust collection adapter
Connect the suction hose to collect saw dust with the
vacuum cleaner (see Fig. 11).
Optional accessory is subject to change without notice.
APPLICATION
Cutting various types of wood.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a power receptacle while
the power switch is in the ON position, the power
tool will start operating immediately, which could
cause a serious accident.
8.
9.
10.
11.
12.
13.
90°
45°
3. Extension cord
4. Prepare a wooden workbench (Fig. 1)
CAUTION
ADJUSTING THE SAW PRIOR TO USE
1. Adjusting the cutting depth
2. Installing riving knife
(1) Place the base facing upward and loosen the clamp
(2) Install the riving knife to the arm securely with the
Ensure that the retraction mechanism of the guard
system operates correctly.
The saw blades body must be thinner than the
riving knife and the width of cut, or kerf (with
teeth set) must be greater than the thickness of
the riving knife.
Never operate the circular saw with the saw blade
turned upward or to the side.
Ensure that the material is free of foreign matter
such as nails.
The riving knife should always be used except
when plunging in the middle of the work piece.
The saw blades should be from 305 mm to 335
mm external diameter ranges.
(110V, 220V, 230V, 240V)
128 mm
85 mm
1560 W
3400/min.
13 kg
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
Since the saw blade will extend beyond the lower
surface of the lumber, place the lumber on a
workbench when cutting. If a square block is utilized
as a workbench, select level ground to ensure it
is properly stabilized. An unstable workbench will
result in hazardous operation.
To avoid possible accident, always ensure that the
portion of lumber remaining after cutting is securely
anchored or held in position.
As shown in Fig. 2 cutting depth adjustment can
be accomplished by loosening clamp lever and
shifting the base. When the base and saw blade
are at a perpendicular angle, use the link scale to
adjust the cutting depth.
Measure the distance that the saw blade extends
to adjust the cutting depth to the correct distance
because the scale marks are only indicated for
reference. After the adjustment is over, securely
tighten the clamp lever.
lever. Lift the base until the depth of cut on the
main unit reaches the minimum state, fasten the
clamp lever, and secure the base. (Fig. 2)
2 attached bolts. (Fig. 3)
English
5

Publicidad

Tabla de contenido
loading

Tabla de contenido