Publicidad
Idiomas disponibles
Idiomas disponibles
Accessories/Options
Check you have all the items shown.
Accessories
□
□
Remote Control
Transmitter
•
EUR7737Z10
□
Cable clamper
(2)
□
□
Pedestal
•
•
TBL2AX00021
TBL2AX00061
(TH-42PX600U)
(TH-50PX600U)
Installing remote's batteries
1
Open
Hook
Caution
•
Incorrect installation may cause battery leakage and corrosion, resulting in damage to the remote control unit.
Do not mix old and new batteries.
Do not mix different battery types (such as alkaline and manganese batteries).
Do not use rechargeable (Ni-Cd) batteries.
•
Do not burn or break batteries.
•
Make a note of the remote control codes before changing batteries in case the codes are reset. (p. 49-50)
Optional accessories
Wall-hanging bracket
(angle)
•
Wall-hanging bracket (vertical)
•
TY-WK42PR3U
TY-WK42PV3U
(TH-42PX600U,
(TH-42PX600U,
TH-50PX600U)
TH-50PX600U,
TH-58PX600U)
Note
•
In order to maintain the unit's performance and safety, be absolutely sure to ask your dealer or a licensed
contractor to secure the wall-hanging brackets.
•
Carefully read the instructions accompanying the plasma TV stand or pedestal, and be absolutely sure to take
steps to prevent the TV from tipping over.
•
Handle the TV carefully during installation since subjecting it to impact or other forces may cause its paneling to
crack.
6
□
Batteries for the Remote
Antenna Adapter
•
Control Transmitter
F-Type
•
(2)
for 5C-2V
AA Battery
□
IR Blaster
AC cord
•
□
TBL2AX00071
Operating Instructions
(TH-58PX600U)
□
Product Registration Card
(U.S.A.)
□
Customer Care Plan Card
(U.S.A.)
2
Close
Note the correct polarity (+ or -).
Plasma TV stand
•
TY-S42PX600W
(TH-42PX600U)
•
TY-S50PX600W
(TH-50PX600U)
•
TY-S58PX600W
(TH-58PX600U)
Attaching the pedestal to the plasma television
Warning
Do not disassemble or modify the pedestal.
•
Otherwise the unit may fall over and become damaged, and personal injury may result.
Caution
Do not use any television or displays other than those given in this manual.
•
Otherwise the unit may fall over and become damaged, and personal injury may result.
Do not use the pedestal if it becomes warped or physically damaged.
•
If you use the pedestal while it is physically damaged, personal injury may result. Contact your nearest Panasonic
Dealer immediately.
During setting-up, make sure that all screws are securely tightened.
•
If sufficient care is not taken to ensure screws are properly tightened during assembly, the pedestal will not be strong enough to
support the plasma television, and it might fall over and become damaged, and personal injury may result.
Use the accessory fall-prevention brackets to secure the plasma television.
•
If the unit is knocked or children climb onto the pedestal with the Plasma TV installed, the plasma television may
fall over and personal injury may result.
Two or more people are required to install and remove the television.
•
If two people are not present, the television may be dropped, and personal injury may result.
Accessories for pedestal assembly
Assembly screw
Assembly screw
Pole (2)
A
B
C
(4)
(4)
(for 42˝ and 50˝) M5 x 18
(for 58˝) M5 x 25
M5 x 65
1
Assembling the pedestal
Using the four assembly screws
, securely fasten the left and right poles to the base, as shown in the
A
illustration below.
Pole
Front
a
A
(
)
Pole
Align the stamped marks.
2
Setting-up
Television unit
B
Pedestal
Label
Base (1)
Band (2)
D
E
Pole
b
( )
Pole
Front
Align the stamped marks.
* Carry out work on a horizontal and level surface.
Lift the television unit above the pedestal
base, with the back of the display unit on
the same side as the Label. Then align the
holes in the television unit with the poles of
the pedestal and lower the television unit into
place.
B
Use the assembly screws
(M5 x 65) to
B
fasten securely.
Rear
7
Publicidad
