Bosch Professional GBH 185-LI Manual Original página 22

22 | English
Do not continue to use the power tool if the damping
u
element is damaged.
Inserting screwdriver bits (see figure I)
Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
A universal holder (22) with SDS plus shank is required to
work with screwdriver bits.
– Clean and lightly grease the insertion end of the shank.
– Insert the universal holder into the tool holder while turn-
ing it until it locks automatically.
– Check that it is locked by pulling the universal holder.
– Insert a screwdriver bit in the universal holder. Only use
screwdriver bits that fit the screw head.
– To remove the universal holder, slide the locking sleeve
(4) backwards and remove the universal holder (22)
from the tool holder.
Attaching the Fall Protection System (see figure J)
Note: A fall protection system (24) that is suitable for the
weight of the entire system should be used to prevent the
power tool from falling. The maximum permitted length of
the fall protection system is 1.8 m. Please always refer to the
permitted attachment area (23) on the power tool.
It is best to use the fall protection system with a tape loop se-
cured by an anchor knot or a fall protection system with fall
damper.
Please always refer to the operating instructions when at-
taching the fall protection system (24).
Always secure the opposite side of the fall protection
u
system to a stable structure (e.g. a building or scaf-
folding) and never to the user.
The fall protection system must be able to move freely
and may only be attached to the power tool at the
fixed anchorage point (25) and in the permitted at-
tachment area(23) .
Select the fixed anchorage point (25) such that the
power tool can fall freely into the fall protection sys-
tem without wrapping around or putting the user at
risk of harm in the event of a fall.
Never use the fall protection system on a power tool
which has been fitted with the GDE 12 dust extraction
attachment.
Maintenance and Service
Maintenance and Cleaning
Before carrying out any work on the power tool (e.g.
u
maintenance, tool change etc.), remove the battery
from the power tool. There is risk of injury from uninten-
tionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Replace a damaged dust protection cap immediately.
u
It is recommended that you have use an after-sales
service for this.
1 609 92A 9ER | (24.05.2024)
– Clean the tool holder (2) after each use.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
When the batteries are shipped by third parties (e.g. air
transport or forwarding agency), special requirements on
packaging and labelling (e.g. ADR regulations) must be met.
A dangerous goods expert must be consulted when prepar-
ing the items for shipping.
Dispatch battery packs only when the housing is undam-
aged. Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in the
packaging. Please also observe the possibility of more de-
tailed national regulations.
Disposal
Power tools, rechargeable batteries, accessor-
ies and packaging should be sorted for environ-
mental-friendly recycling.
Do not dispose of power tools and batteries/re-
chargeable batteries into household waste!
Only for EU countries:
Power tools that are no longer suitable for use and defective
or used batteries must be disposed of separately. Use the
designated collection systems.
Bosch Power Tools