cecotec ENERGYSILENCE 4200 Serie Manual De Instrucciones página 23

ENGLISH
2. BEFORE USE
- This appliance is packaged in a way as to protect it during transport. Take the appliance
out of its box and remove all packaging materials. You can keep the original box and other
packaging elements in a safe place. This will help you prevent damage to the appliance
when transporting it in the future. In case the original packaging is disposed of, make sure
all packaging materials are recycled accordingly.
- Make sure all parts and components are included and in good conditions. If there is any
piece missing or in bad conditions, contact the official Cecotec Technical Support Service
immediately.
Box content
- Fan
- Remote control
- Assembly kit
- Instruction manual
- Remote control batteries (2 x AAA)
3. INSTALLATION
Pre-assembly preparation
- To prevent personal injury and damage, make sure that the location where the appliance
is going to be installed allows a 2.3-metre clearance from the blades to the floor and a
76-cm clearance from the blades to any wall or object. Fig. 3
- Make sure that the building structure can hold the full weight of the fan.
- This fan can be installed on a normal or vaulted ceiling with a downrod. The hanging
length of the fan can be extended with a longer rod. Fig. 4
- Ensure that the junction box is securely fastened to the building structure and can
support the full weight of the fan.
- Installation requires the following tools: screwdriver, flat screwdriver, adjustable pliers
or spanner, ladder, wire cutters and electrical tape.
Fig. 4 key:
A. Standard assembly
B. Angle assembly
Mounting bracket installation
- Wooden ceiling. Fig. 5
- Concrete ceiling. Fig. 6.
44
ENERGYSILENCE AERO 4200 WHITEWOOD/ GOLDWHITEWOOD/ BLACK&WHITEWOOD
WHITE&DARKWOOD/ GOLDDARKWOOD/ BLACK&DARKWOOD
1. Drill a ⌀8 mm hole in the ceiling and insert the bolt. Align the bracket with the hole and
tighten it with the nut.
Fan assembly and suspension. Fig. 7
Fig. 7 key:
1. Electric wiring
2. Hanging ball slot
Clevis
3.
4. Adapter
5. Canopy
6. Decorative cover
Pin
7.
8. Locking screw
- If you want the fan to hang lower, you must remove the hanging ball from the supplied 6
inch downrod for use with a longer rod (included). (If you wish to use the 6-inch downrod,
follow the steps below).
- To remove the hanging ball, loosen the suspension ball locking screw and remove the
pin and clip. Lower the hanging ball and remove the clevis pin. Slide the hanging ball off
the downrod, and slide it onto the longer rod (note that the top of the rod has a hole for
the locking screw). Insert the stop pin into the top of the extended downrod and raise the
hanging ball. Make sure that the stop pin is aligned with the slots on the inside of the
hanging ball, tighten the fixing screw securely.
- Tip: To prepare for passing the electrical wires through the rod, attach a small piece of
electrical tape to the ends of the electrical wires to hold them together when passing them
through the rod.
Loosen the fixing screws and nut on the top of the motor housing. Remove the pin and rod
2.
clip (if you have not already done so). Slide the rod down through the canopy.
3. Pass the electrical wires through the rod and pull the wires protruding from the top of
the rod end.
Place the downrod in the anchorage of the motor housing and insert the previously
4.
removed pin. Tighten the fixing bolts and the main-body attachment nut securely. Lower
the canopy onto the motor housing
Connection of the remote-control receiver. Fig. 8
Canopy assembly. Fig. 9
5. Lift the canopy up to the mounting bracket, aligning the loosened screws in the bracket
with the holes in the canopy. Turn the canopy to lock it. Re-insert the screws and secure
them all with a screwdriver.
ENERGYSILENCE AERO 4200 WHITEWOOD/ GOLDWHITEWOOD/ BLACK&WHITEWOOD
WHITE&DARKWOOD/ GOLDDARKWOOD/ BLACK&DARKWOOD
ENGLISH
45