ENGLISH
6.
Once you have secured the mounting bracket to the connection cover, you can hang the
fan. Hold the fan firmly with both hands. Slide the downrod through the opening in the
mounting bracket and allow the ball to rest on the bracket. Rotate the hole in the hanging
ball until it aligns with the tab on the mounting bracket.
Tip: have someone else hold the ladder securely and bring the fan closer to you once it is on
the ladder.
Blade assembly. Fig. 10
7.
First, attach the blades to the circular part. Do not fix them all at once. Once finished,
attach the blades to the motor.
LED-light assembly
8.
Unscrew the screws. Attach the LED plate to the bottom of the fan by inserting the fixing
screws into the holes. Then turn it until it is firmly in place. Then screw in the previous
fixing screw by aligning the hole in the screw and the hole in the bottom of the fan. Finally,
tighten the other two fixing screws to secure the LED plate. Fig. 11
NOTE: during the installation or when the LED lamp is removed, keep the insulation pads intact.
Over-tightening the screws may damage them.
9.
Connect the LED to the LED lamp panel as shown in Figure 12, and then securely fasten
them with the decorative clips and nuts. Fig. 12
10. Position the panel as shown in figure 13.
4. OPERATION
Remote control
Fig. 14 key:
1.
Power indicator light
2.
Speed buttons
3.
Off button
Timer buttons
4.
5.
Light button
6.
Winter/summer function (reversal of blade rotation direction)
-
The indicator light will light up while the appliance is running.
-
Use the 3 speed buttons to select the air power level: low, medium, or high.
-
Press the power button to turn the appliance off.
-
Use the timer buttons to select the fan operating time. The fan will switch off once the
46
ENERGYSILENCE AERO 4200 WHITEWOOD/ GOLDWHITEWOOD/ BLACK&WHITEWOOD
WHITE&DARKWOOD/ GOLDDARKWOOD/ BLACK&DARKWOOD
selected time has elapsed.
-
Press the light button to turn the fan's lamp on and off.
Winter/Summer function
To activate the switch, press the Winter/Summer Function button on the remote control. This
button allows you to change the rotating direction (clockwise or counterclockwise) of the fan
blades.
Winter Function
Press the Winter/Summer Function button, if the blades start to rotate clockwise, this mode
is activated (causing the warm air to be distributed throughout the room), otherwise press the
button again.
Summer Function
Press the Winter/Summer Function button for the blades to start rotating counterclockwise
(causing a cool breeze). If this does not occur, press the button again.
Warning
Invert the spinning direction of the fan while in operation. Hold down the button for approx.
3 seconds: the appliance will beep, and the blades will start slowing down until they stop
spinning. After a few seconds, they will start spinning again in the opposite direction
Warnings
-
The remote control operates through RF Wireless digital transmission technology. If both
the fan and the lamp are equipped with a switch, turn on the fan at top speed and turn the
light on before using the remote control.
-
If the fan or the light cannot be controlled through the remote control, check if the batteries
in the remote control are in good conditions and if they make good contact, that the positive
and negative electrodes are in the correct position, and if the batteries are charged.
-
If the fan or the light cannot be controlled through the remote control, check if there are
other remote-controlled appliances in the same area and check if the transmitter buttons
are pressed. Appliances with similar remote-control systems may cause interference. This
does not include infrared remote controls.
-
Pay attention to the appliance voltage. Too low a voltage may cause the remote control to
not work. The technical specifications are indicated in this manual.
-
If the remote control is not going to be used for a long time, remove the batteries.
ENERGYSILENCE AERO 4200 WHITEWOOD/ GOLDWHITEWOOD/ BLACK&WHITEWOOD
WHITE&DARKWOOD/ GOLDDARKWOOD/ BLACK&DARKWOOD
ENGLISH
47